Rear essentric lockout bolt kit?

SPOHN · 08-26-2013, 07:47 PM

Quote:

Originally Posted by synolimit

See that's why I want the lockout kit. Once I get camber arms and toe arms, I want all the adjustment there and not at my bolt locations. A smooth bolt won't move like an eccentic bolt can. "If" I installed these ahead of time I was only planning on the control arm and not the toe arm. But if toe does move even with just messing with the camber bolt, then I won't touch anything.

Really it's the same tattoo??

OFF Topic.

It's close enough

synolimit · 08-26-2013, 08:01 PM

Quote:

Originally Posted by phunk

I am very curious to see exactly what you are planning on doing.

Lol I'm just making this...

And paying $8 instead of $72. The whole topic start though was asking if I install now what will my suspension do. But you answered that so ill either wait or just ghetto measure toe and camber like I said and hope the bolts with no adjustment don't give me insane outta wack numbers.

synolimit · 08-26-2013, 08:08 PM

Quote:

Originally Posted by SPOHN

OFF Topic.

O nice. This arms a full sleeve just not filled in yet

synolimit · 08-26-2013, 08:12 PM

Quote:

Originally Posted by phunk

that just sounds like a regular eccentric bolt kit?

Yep, just not paying $72

Quote:

Originally Posted by modme

It would no longer be adjustable and no slip. Assuming suspension geometry doesnt change, camber and toe will always stay the same.

Correct. Once I get the arms, the adjustable bolts are going bye bye so they can't slip under a hard G load.

Quote:

Originally Posted by Cbtech

***retard moment here

***

what is this supposed to do??

Read right above

synolimit · 08-26-2013, 10:14 PM

Well I just measured toe. Not ideal, 1. Because I used a tape measure and 2. The only way to measure was not in the middle of the wheel. I got only about 1/4 way up the tire. However I did get a rear measurement of about 68 1.5/16th and a front measurement of 68. Therefore the rear tires are toed in 1.5/16th of an inch. That's factory yes?

synolimit · 08-27-2013, 03:27 PM

Well I'm inpatient so I decided to see what would change by installing the toe bolts. To my surprise the numbers didn't do what I was thinking they'd do.

Before install...
Driver camber -1.9
Passenger cam -1.4
Rear toe 0.094"

After install
Driver camber -1.8
Passenger cam -1.3
Rear toe 0.094"

Basically nothing happened which is awesome! Because 1. I don't need to take them off and 2. Everything's in spec.

Now I was scared because first I just installed the passenger side and measured and the toe was at 0.25" which is out of spec. I thought "o great, after the drivers side ill be 0.5" or something. But doing the drives pulled it right back where it was. Now I did look at the factory marks and it looked like the eccentric bolts were straight up and down so they weren't giving any adjustment anyhow. Later ill tackle the camber bolts.

Spec Jay · 08-27-2013, 04:27 PM

you need to slot the subframe and drill the washers with offset holes.

Sh0velMan · 08-27-2013, 04:52 PM

So uhh what sizes and offsets did you end up going with to make RPF1's fit?

synolimit · 08-27-2013, 06:04 PM

Quote:

Originally Posted by Spec Jay

you need to slot the subframe and drill the washers with offset holes.

Huh? Why?

Whole point of this was to have zero chance of movement from those locations.

synolimit · 08-27-2013, 06:05 PM

Quote:

Originally Posted by Sh0velMan

So uhh what sizes and offsets did you end up going with to make RPF1's fit?

10.5 +15 rear and 9.5 +45 front with a 20mm spacer.

Sh0velMan · 08-28-2013, 08:59 AM

Quote:

Originally Posted by synolimit

10.5 +15 rear and 9.5 +45 front with a 20mm spacer.

How tight is the clearance between the caliper and wheel in the front with that spacer?

Think you could have pulled it off with +38 and a 15mm? That's 2mm less clearance.

Sh0velMan · 08-28-2013, 09:00 AM

Quote:

Originally Posted by synolimit

Huh? Why?

Whole point of this was to have zero chance of movement from those locations.

I *think* he was trying to tell you how you could adjust the setup using the lockout plates, without using eccentric bolts... He missed the part about your alignment being fine and you planning on getting adjustable arms anyway, I guess.

synolimit · 08-28-2013, 12:49 PM

Quote:

Originally Posted by Sh0velMan

How tight is the clearance between the caliper and wheel in the front with that spacer?

Think you could have pulled it off with +38 and a 15mm? That's 2mm less clearance.

Yes I could have. Odd thing is with the 20mm I have like zero clearance. But I put the 15mm on, held the rim flat on it and spun and nothing hit.

synolimit · 08-28-2013, 12:52 PM

Quote:

Originally Posted by Sh0velMan

I *think* he was trying to tell you how you could adjust the setup using the lockout plates, without using eccentric bolts... He missed the part about your alignment being fine and you planning on getting adjustable arms anyway, I guess.

How would u adjust toe with a lockout plate and no eccentric bolt?

Sh0velMan · 08-28-2013, 03:14 PM

Quote:

Originally Posted by synolimit

How would u adjust toe with a lockout plate and no eccentric bolt?

By making the hole not round... slotted, in other words. See what I mean?

08-26-2013, 10:14 PM	#20 (permalink)
synolimit A True Z Fanatic Join Date: May 2013 Location: Columbus, OH Posts: 5,051 Drives: 2013 Silver 370z Rep Power: 3389	Well I just measured toe. Not ideal, 1. Because I used a tape measure and 2. The only way to measure was not in the middle of the wheel. I got only about 1/4 way up the tire. However I did get a rear measurement of about 68 1.5/16th and a front measurement of 68. Therefore the rear tires are toed in 1.5/16th of an inch. That's factory yes? __________________ 13 370z-

08-27-2013, 03:27 PM	#21 (permalink)
synolimit A True Z Fanatic Join Date: May 2013 Location: Columbus, OH Posts: 5,051 Drives: 2013 Silver 370z Rep Power: 3389	Well I'm inpatient so I decided to see what would change by installing the toe bolts. To my surprise the numbers didn't do what I was thinking they'd do. Before install... Driver camber -1.9 Passenger cam -1.4 Rear toe 0.094" After install Driver camber -1.8 Passenger cam -1.3 Rear toe 0.094" Basically nothing happened which is awesome! Because 1. I don't need to take them off and 2. Everything's in spec. Now I was scared because first I just installed the passenger side and measured and the toe was at 0.25" which is out of spec. I thought "o great, after the drivers side ill be 0.5" or something. But doing the drives pulled it right back where it was. Now I did look at the factory marks and it looked like the eccentric bolts were straight up and down so they weren't giving any adjustment anyhow. Later ill tackle the camber bolts. __________________ 13 370z- Last edited by synolimit; 08-27-2013 at 03:30 PM.

08-27-2013, 04:27 PM	#22 (permalink)
Spec Jay A True Z Fanatic Join Date: Apr 2009 Location: Bummerton Posts: 1,510 Drives: MtB 09 370z Rep Power: 19	you need to slot the subframe and drill the washers with offset holes. __________________ 09 Monterey Blue Global Time Attack Street Class Build Build Thread:Saber! Instagram:@SpecJay

08-27-2013, 04:52 PM	#23 (permalink)
Sh0velMan A True Z Fanatic Join Date: Jan 2012 Location: Dallas/Ft.Worth Posts: 3,349 Drives: Noisily. Rep Power: 20	So uhh what sizes and offsets did you end up going with to make RPF1's fit? __________________ Buy My Car! \| Build Thread

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New SPC Rear Camber arm and bolt set	Z_bro	Tires/Wheels	0	05-25-2013 12:14 PM
Ichiba 20mm Bolt On Rear Spacers - Installed!	joshs09slvrZ	Brakes & Suspension	17	02-14-2012 08:50 PM
lockout video while car is in motion	nappymike	Audio & Video	18	03-26-2009 03:03 PM