Traction Control Anti Slip ISSUE

Carbon_z · 07-24-2012, 12:49 PM

So a while back I had an accident and the damage was on the front passenger wheel. The ENTIRE wheel hub, spindle, rotor, caliper, brake line, abs, wheel was snapped off the car. Well since then the car has been repaired and just had an alignment done on the car with my new set of 20's. So my issue, the light is still ON and the VDC button wont respond but light remains on as well. Any way to fix this issue?

HOpefully that gives you enough about the topic.

b1adesofcha0s · 07-24-2012, 01:04 PM

The same thing happened when I had my last accident in my car. I drove over a tire shred on a highway ramp (in the rain), slid onto the grass, and then bumped the guard rail. The slip light and the VDC light stayed on after it happened, but they went away after I turned the car off and started it back up again.

mt007jb · 01-10-2015, 02:30 AM

So I am having the same issue as you b1adesofcha0s, my skid light and VDC off light stayed on, after restarting the car, they turn off. Brake light isn't coming on at all though, just the traction lights. What's worrisome to me is that it happens after hitting a few skid patches on the highway (I'm currently in Germany where there's a lot of ice and slush on the roads at times). It'll usually happen when accelerating a bit hard, the lights will come on, I'll restart the car and all seems to be fine. Any idea what causes this? Is this just a pushing too much on the car thing and be nicer under nasty weather conditions? Or do I need to fork over way too much Euro to some German Nissan dealer to get it fixed?

Carbon_z · 07-24-2012, 01:09 PM

I was hoping it would go away but unfortunately it hasnt. Since I had to replace the entire wheel assembly on the front passenger I wasnt sure if something was missing like a sensor. Also find it weird the traction light is on as I figured the rear would be the one to affect the light

b1adesofcha0s · 07-24-2012, 01:16 PM

Maybe you could try disconnecting the battery to clear them?

ChrisSlicks · 07-24-2012, 01:22 PM

This will happen if the controller isn't getting a signal from all the wheel speed sensors. So are you seeing the "VDC Off" and the slip light and the ABS light? Or just the VDC off light by itself?

Carbon_z · 07-24-2012, 01:18 PM

oh its been disconnected several times and replaced. Is there a traction/antiskid sensor in the front passenger wheel?

I bought a AbS sensor off ebay, do I need to program it or anything? thats the only sensor I am aware of.

Mike · 07-24-2012, 07:03 PM

you need to take it to a dealer and have them hook the consult machine up to it to see what the problem is. I recommend SUtherlin. Mine was a piece of track rubber in between the hub and the sensor

Carbon_z · 07-24-2012, 07:29 PM

The abs light is not on... Just the vdc light and the Losing traction icon light is on. Which hub would have the sensors the ones on the back? Because the front passenger is completely new but never bought a sensor other than abs. The rest of them have had new struts, springs, rotors and pads installed so I would think setting stuck would have been seen.

Carbon_z · 07-26-2012, 01:29 PM

anybody have a picture of the speed sensor? Also do all the wheels have the speed sensor? I thought the only wires i saw were related to the ABS, which isnt on.

ChrisSlicks · 07-26-2012, 02:51 PM

Quote:

Originally Posted by billet370

anybody have a picture of the speed sensor? Also do all the wheels have the speed sensor? I thought the only wires i saw were related to the ABS, which isnt on.

It's the same sensor for both. All 4 wheels have the wheel speed sensor which is used for ABS and traction control.

Carbon_z · 07-26-2012, 03:29 PM

I replaced the ABS sensor for the FRONT PASSENGER wheel. Since it was not the same sensor that came on the car should I have to program it or anything??? The ABS light was on previously and since the sensor was installed the ABS light went off but the 2 others remain.

ChrisSlicks · 07-26-2012, 03:51 PM

Quote:

Originally Posted by billet370

I replaced the ABS sensor for the FRONT PASSENGER wheel. Since it was not the same sensor that came on the car should I have to program it or anything??? The ABS light was on previously and since the sensor was installed the ABS light went off but the 2 others remain.

No programming is required. I would check the controller that is under the plastic cover near the e-brake and make sure that it has power.

wheee! · 07-26-2012, 04:12 PM

May not be related but are you low on brake fluid?......

Carbon_z · 07-26-2012, 08:15 PM

Brake fluid has been replaced even new brakes. The whole car went through an overhaul. But what I'm trying to understand is what the speed sensor looks like. Anybody have a picture of it on the front passenger wheel? I would love for ever Eva.

07-24-2012, 12:49 PM	#1 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	Traction Control Anti Slip ISSUE So a while back I had an accident and the damage was on the front passenger wheel. The ENTIRE wheel hub, spindle, rotor, caliper, brake line, abs, wheel was snapped off the car. Well since then the car has been repaired and just had an alignment done on the car with my new set of 20's. So my issue, the light is still ON and the VDC button wont respond but light remains on as well. Any way to fix this issue? HOpefully that gives you enough about the topic. __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at http://www.instagram.com/carbonz.

07-24-2012, 01:04 PM	#2 (permalink)
b1adesofcha0s A True Z Fanatic Join Date: Jan 2011 Location: MD Posts: 40,963 Drives: HypeTrain Choo Choo! Rep Power: 142	The same thing happened when I had my last accident in my car. I drove over a tire shred on a highway ramp (in the rain), slid onto the grass, and then bumped the guard rail. The slip light and the VDC light stayed on after it happened, but they went away after I turned the car off and started it back up again. __________________ Project: b1adeZmobile (2009 370Z) \| Uprev Tune by AAM Competition \| Berk Exhaust Project: b1adeZmobile 2.0 (2014 C7 Z51) \| Corsa Xtreme Exhaust

01-10-2015, 02:30 AM	#3 (permalink)
mt007jb Base Member Join Date: Jan 2013 Location: London, GBR Posts: 3 Drives: 09 Z Sil Tour Spt 6M Rep Power: 13	So I am having the same issue as you b1adesofcha0s, my skid light and VDC off light stayed on, after restarting the car, they turn off. Brake light isn't coming on at all though, just the traction lights. What's worrisome to me is that it happens after hitting a few skid patches on the highway (I'm currently in Germany where there's a lot of ice and slush on the roads at times). It'll usually happen when accelerating a bit hard, the lights will come on, I'll restart the car and all seems to be fine. Any idea what causes this? Is this just a pushing too much on the car thing and be nicer under nasty weather conditions? Or do I need to fork over way too much Euro to some German Nissan dealer to get it fixed? Last edited by mt007jb; 01-10-2015 at 02:32 AM.

07-24-2012, 01:09 PM	#4 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	I was hoping it would go away but unfortunately it hasnt. Since I had to replace the entire wheel assembly on the front passenger I wasnt sure if something was missing like a sensor. Also find it weird the traction light is on as I figured the rear would be the one to affect the light __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at http://www.instagram.com/carbonz.

07-24-2012, 01:16 PM	#5 (permalink)
b1adesofcha0s A True Z Fanatic Join Date: Jan 2011 Location: MD Posts: 40,963 Drives: HypeTrain Choo Choo! Rep Power: 142	Maybe you could try disconnecting the battery to clear them? __________________ Project: b1adeZmobile (2009 370Z) \| Uprev Tune by AAM Competition \| Berk Exhaust Project: b1adeZmobile 2.0 (2014 C7 Z51) \| Corsa Xtreme Exhaust

07-24-2012, 01:22 PM	#6 (permalink)
ChrisSlicks A True Z Fanatic Join Date: Mar 2009 Location: North East Posts: 6,203 Drives: 09 370Z Sport M6 Rep Power: 653	This will happen if the controller isn't getting a signal from all the wheel speed sensors. So are you seeing the "VDC Off" and the slip light and the ABS light? Or just the VDC off light by itself? __________________ Hotchkis ARB \| Stillen CAI \| Art Pipes \| Berk CBE \| Stillen AP Racing Brakes \| AE Performance Oil Cooler \| BC Racing ER Coilovers \| Doran Control Arms

07-24-2012, 01:18 PM	#7 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	oh its been disconnected several times and replaced. Is there a traction/antiskid sensor in the front passenger wheel? I bought a AbS sensor off ebay, do I need to program it or anything? thats the only sensor I am aware of. __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at http://www.instagram.com/carbonz.

07-24-2012, 07:03 PM	#8 (permalink)
Mike The370Z.com Sponsor Join Date: Jun 2009 Location: Loganville, GA Posts: 5,944 Drives: 370z Rep Power: 2186	you need to take it to a dealer and have them hook the consult machine up to it to see what the problem is. I recommend SUtherlin. Mine was a piece of track rubber in between the hub and the sensor __________________ NISSAN: 75 280Z / 86 300ZX GLL /87 Sentra SE / 03 350Z / 23 Z Porsche: 93 968 / 23 Macan GTS / 93 968

07-24-2012, 07:29 PM	#9 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	The abs light is not on... Just the vdc light and the Losing traction icon light is on. Which hub would have the sensors the ones on the back? Because the front passenger is completely new but never bought a sensor other than abs. The rest of them have had new struts, springs, rotors and pads installed so I would think setting stuck would have been seen. __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at http://www.instagram.com/carbonz.

07-26-2012, 01:29 PM	#10 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	anybody have a picture of the speed sensor? Also do all the wheels have the speed sensor? I thought the only wires i saw were related to the ABS, which isnt on. __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at http://www.instagram.com/carbonz.

07-26-2012, 03:29 PM	#12 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	I replaced the ABS sensor for the FRONT PASSENGER wheel. Since it was not the same sensor that came on the car should I have to program it or anything??? The ABS light was on previously and since the sensor was installed the ABS light went off but the 2 others remain. __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at http://www.instagram.com/carbonz.

07-26-2012, 04:12 PM	#14 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 58 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	May not be related but are you low on brake fluid?...... __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

07-26-2012, 08:15 PM	#15 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	Brake fluid has been replaced even new brakes. The whole car went through an overhaul. But what I'm trying to understand is what the speed sensor looks like. Anybody have a picture of it on the front passenger wheel? I would love for ever Eva. __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at http://www.instagram.com/carbonz.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
traction control	wfmrules3	Engine & Drivetrain	19	04-19-2014 09:51 PM
Hello from sunny North Carolina -- 370Z Traction control vs VDC issue	JoeyD	New 370Z Owner	42	11-15-2012 05:24 PM
traction control?	RedNismoZ	Nismo 370Z	10	12-30-2011 03:11 PM
ABS+traction control+slip lights all on please help	zuperman 370	Wheels & Tires	16	06-15-2011 12:07 PM
Traction control	bigZ	Nissan 370Z General Discussions	21	03-09-2011 11:17 PM