Lowered on Swifts. Still scraping!

kenchan · 07-12-2012, 04:50 PM

Quote:

Originally Posted by future370zzz

I guess if I were to leave it on, over time it would just wear down until it either doesn't scrape anymore or it breaks off. I don't see how it would break off.

As long as I don't scrape my bumper I don't care what happens to the plastic underneath there I guess. Anyone thinking the same thing?

i forget who it was, but someone trimmed the front center deflector using a dremel. looked pretty good. you know how the sides of the deflector comes down lower than the center. he trimmed that part off so it's a straight cut.

Juruki · 07-12-2012, 05:11 PM

I've been scraping those things for over 2 years and they are still there. The rubber is very soft so it won't break or crack. My car is a lot lower than ppl with swift springs btw

tjlazer · 07-12-2012, 05:25 PM

I use to scape those when I was stock! Yeah they are made of rubber just leave them on and let it scrape. As far as the front one that runs along the middle you can use sand paper to clean it up after a while when it gets bad. The swifts lower 1.2" front so if you don't want it that low get a different spring. Eibach lowers less and if you get RS*R or Tein H Tech from Japan those lower even less.

speedfreek · 07-12-2012, 05:29 PM

Quote:

Originally Posted by wheee!

I did this until it cracked and started hanging off on one side.... then i took it off. I left the wind deflectors in front of the wheels for a while too, but then they started pulling off too...

Hmm mine will eventually come off as well as I want to put the Stillen lip on it color matched. Unless I decide to go with something else. Either way I will end up worry about scraping the lip kit at that point though. My springs should be sitting on the doorstep by now. Question is do I install them now or wait until after I install my exhaust that supposed to come in this month? I want to wait but going to be hard with all the parts sitting around waiting to go swift/spc/spacers. The car should be coming along nicely by Z Nationals which I hope to make it to.

B&W_Evader · 07-12-2012, 09:24 PM

This is why I don't think I'll ever lower my Z. I'm supper gentle on driveways and speed bumps. Never touch the speed bumps but do scrape every once in a while on a steep driveway. Mainly when I don't make the entry angle sharp enough. I probably should measure the lip and see if mine's a little lower than average.

tjlazer · 07-12-2012, 11:31 PM

I never scrape (Nismo bumper lip) on speed bumps or driveways unless they are really bad. Rolling curbs are bad too so I got Bridjit curb ramps for home.

MyKindaGuise · 07-12-2012, 11:55 PM

Quote:

Originally Posted by future370zzz

Yeah, I haven't trimmed or removed anything so I scrape. I come in at about 45 degrees mostly because some of the driveway are vary narrow so I can't really cut in any more.

Please post a pic!

Damn I forgot to at tonights meet. I will post tomorrow. Seriously just trim the corners back to make it all one solid flush line and it'll make a big difference.

ZeN · 07-13-2012, 10:29 PM

I've been running swift with the front chin for almost 2 yrs, the chin still looks good up front. It get scrape almost everytime i'm at bump / taking it at 45 deg angle. I've even scrape my flexible joint on the stock exhaust / underbody - cut & replace it couple of time. Yes it only drop on Swift, we have some high+short bumper here in Malaysia. Cant even imagine dropping any lower than swift..lol

Zoren 370 · 07-14-2012, 11:59 AM

Don't take out the wind deflectors it bends anyway so it won't really hurt if you scrape.
You can't have it all in life...You lowered it so expect the worst.
It would be really hard to drive it if its your DD.
I do have an ARK grip but never scrape it yet.
I usually plan my route if Im using the Z to avoid high speed bumps.
Its really a PAIN but thats the price you pay for looking good.

wheee! · 07-14-2012, 12:48 PM

My wind deflectors started pulling away from the underbody, and looked crappy so off they came. Not a big deal.

CrownR426 · 07-23-2012, 10:51 PM

I removed my chin spoiler the day I took my Z home.
lol!
Seemed useless to me.

07-12-2012, 05:11 PM	#17 (permalink)
Juruki Track Member Join Date: Mar 2010 Location: SoCal Posts: 965 Drives: 370Z Tour/Sport/Navi Rep Power: 16	I've been scraping those things for over 2 years and they are still there. The rubber is very soft so it won't break or crack. My car is a lot lower than ppl with swift springs btw __________________ 09 370z - 7AT Volk Racing TE37SL / BC Coilovers / Berk HFC / TopSpeed CBE + Y-Pipe / Mines Spoiler

07-12-2012, 05:25 PM	#18 (permalink)
tjlazer A True Z Fanatic Join Date: Dec 2009 Location: Tacoma Age: 53 Posts: 2,496 Drives: Z34, R35 Rep Power: 19	I use to scape those when I was stock! Yeah they are made of rubber just leave them on and let it scrape. As far as the front one that runs along the middle you can use sand paper to clean it up after a while when it gets bad. The swifts lower 1.2" front so if you don't want it that low get a different spring. Eibach lowers less and if you get RS*R or Tein H Tech from Japan those lower even less. __________________ 2009 370Z Monterey Blue,Nismo Conversion,RE-11's, K&N Typhoon intakes,Blue Kickplates,Homelink,FI 18" CBE,ERZ HFCs,Hotchkis sways, Swift Spec-R, EVO-R Highwing, UPREV

07-12-2012, 09:24 PM	#20 (permalink)
B&W_Evader Track Member Join Date: Aug 2011 Location: CA Posts: 972 Drives: slower than before Rep Power: 387	This is why I don't think I'll ever lower my Z. I'm supper gentle on driveways and speed bumps. Never touch the speed bumps but do scrape every once in a while on a steep driveway. Mainly when I don't make the entry angle sharp enough. I probably should measure the lip and see if mine's a little lower than average. __________________ \|RIP\|6spd-sport\|OSG-LSD\|XP8\|RBF600\|Eibach Sways\|RE-71R\|FI-34Row\|Gen3-CAI\|Yaw P.S.\|

07-12-2012, 11:31 PM	#21 (permalink)
tjlazer A True Z Fanatic Join Date: Dec 2009 Location: Tacoma Age: 53 Posts: 2,496 Drives: Z34, R35 Rep Power: 19	I never scrape (Nismo bumper lip) on speed bumps or driveways unless they are really bad. Rolling curbs are bad too so I got Bridjit curb ramps for home. __________________ 2009 370Z Monterey Blue,Nismo Conversion,RE-11's, K&N Typhoon intakes,Blue Kickplates,Homelink,FI 18" CBE,ERZ HFCs,Hotchkis sways, Swift Spec-R, EVO-R Highwing, UPREV

07-14-2012, 12:48 PM	#25 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	My wind deflectors started pulling away from the underbody, and looked crappy so off they came. Not a big deal. __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

07-13-2012, 10:29 PM	#23 (permalink)
ZeN Base Member Join Date: Apr 2011 Location: Malaysia Posts: 116 Drives: 09 PW 7AT 370z Rep Power: 14	I've been running swift with the front chin for almost 2 yrs, the chin still looks good up front. It get scrape almost everytime i'm at bump / taking it at 45 deg angle. I've even scrape my flexible joint on the stock exhaust / underbody - cut & replace it couple of time. Yes it only drop on Swift, we have some high+short bumper here in Malaysia. Cant even imagine dropping any lower than swift..lol

07-14-2012, 11:59 AM	#24 (permalink)
Zoren 370 A True Z Fanatic Join Date: Mar 2012 Location: FL Posts: 11,018 Drives: 11 Nissan 370 M6 Rep Power: 1913653	Don't take out the wind deflectors it bends anyway so it won't really hurt if you scrape. You can't have it all in life...You lowered it so expect the worst. It would be really hard to drive it if its your DD. I do have an ARK grip but never scrape it yet. I usually plan my route if Im using the Z to avoid high speed bumps. Its really a PAIN but thats the price you pay for looking good.

07-23-2012, 10:51 PM	#26 (permalink)
CrownR426 A True Z Fanatic Join Date: Nov 2008 Location: South Korea Posts: 4,676 Drives: Manual Rep Power: 848	I removed my chin spoiler the day I took my Z home. lol! Seemed useless to me. __________________ Love + Hardwork + Passion RIP SVTRacer

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Dropping on Swifts, help!	Nick911sc	Brakes & Suspension	18	05-25-2012 07:30 PM
Swifts killing my Nismo Struts?	JJ-NISMO	Brakes & Suspension	11	03-26-2012 12:31 PM
Swifts on Gemini CBE?	Cristobal09	Brakes & Suspension	7	12-04-2011 11:11 AM
Will it rub? SSR & Swifts	Fastfatdude	Wheels & Tires	11	11-23-2011 04:56 PM
what am i scraping?	darthanakin23	Nissan 370Z General Discussions	14	08-05-2010 06:10 PM