2-piece slotted rotor.

1slow370 · 09-01-2009, 06:37 AM

I'd be on board for this too as i was looking for some before i bought the stoptechs after i smoked the stock ones

henryv007 · 09-03-2009, 04:58 PM

I may be all wet here but Stop Tech and Stillen do list cross drilled and slotted rotors for our cars, although they all appear to be 1 pc. like the stock. Am I right that the G37 rotors are the same and will fit the 370z as well? If so its worth looking through listings for those cars as well. Any thoughts as to 1 pc. and 2 pc, one being that much betetr than the other? Im new here so sorry for jumping in with a dumb question, but inquiring minds need to know!

Endgame · 09-03-2009, 05:10 PM

actually, good question henryv007. what is the difference between a one piece and two piece rotor performance wise?

import111 · 09-03-2009, 05:27 PM

differences:
1. A 2 piece rotor usually uses an aluminum center (hat) which transfers less heat to the wheel, and there for, wheel bearings and other parts.

2. Because of that aluminum hat listed above, 2 piece rotors weigh less, which lightens the car as a whole, lightens the front (which is good if the front of the car is the heavier part), and gives the brake pads less weight to clamp onto which in turn should make for shorter stopping distance (if the tires can manage).

3. From what I have seen in 2 piece rotors, the cooling veins are better designed to evacuate heat.

wstar · 09-03-2009, 05:54 PM

Quote:

Originally Posted by import111

differences:
1. A 2 piece rotor usually uses an aluminum center (hat) which transfers less heat to the wheel, and there for, wheel bearings and other parts.

2. Because of that aluminum hat listed above, 2 piece rotors weigh less, which lightens the car as a whole, lightens the front (which is good if the front of the car is the heavier part), and gives the brake pads less weight to clamp onto which in turn should make for shorter stopping distance (if the tires can manage).

3. From what I have seen in 2 piece rotors, the cooling veins are better designed to evacuate heat.

Add to number 2: it also reduces the rotating mass being driven by the engine, which means 1 pound shaved on a brake rotor is worth a lot more acceleration-wise than a pound shaved on non-rotating parts of the car.

Endgame · 09-03-2009, 06:57 PM

that is what i figured; just wanted confirmation. THX!!!

Z1Performance · 09-03-2009, 08:43 PM

Quote:

Originally Posted by henryv007

I may be all wet here but Stop Tech and Stillen do list cross drilled and slotted rotors for our cars, although they all appear to be 1 pc. like the stock. Am I right that the G37 rotors are the same and will fit the 370z as well? If so its worth looking through listings for those cars as well. Any thoughts as to 1 pc. and 2 pc, one being that much betetr than the other? Im new here so sorry for jumping in with a dumb question, but inquiring minds need to know!

They fit yes (370Z to G37 Sport with the Akebono calipers)

Stillen uses DBA rotors. They are coming, but not for a little while

Stoptech will have ones in the future, but right now, they can't even really supply the 1 piece ones to their dealers (long delays)

Equinox · 09-04-2009, 10:20 AM

this seems like an easy enough product to make, I wonder how hard it would be to take up this idea and make my own :P Maybe offer black, red, and blue anodized centers

NIZMOZ · 09-04-2009, 10:25 AM

2-Pc Lightweight Rotors for Akebono Brakes - MyG37

2 Piece rotors.....

Equinox · 09-04-2009, 10:30 AM

The good news keeps rolling in - I found these for our stock calipers as well - they are two peice forged aluminum alloy hats, just like the ones you linked Nismoz, but these seem a little more aggressive
370Z (Sport) - RacingBrake.com

19 lbs compared to 30 lbs.

If my rims weighed 30 lbs I sure as hell would be happy with buying lighter 19lb wheels.

edit - apparently they are the same company as the picture posted in Nismoz link - but the rotor looks different in the link I posted. Hm.

Z1Performance · 09-04-2009, 01:18 PM

Weight is all fine and well, but you also need to look at the metallurgy of the disks, and, the mounting that the hat uses. There are many variables to consider

Endgame · 09-04-2009, 01:27 PM

Why are those important??

Equinox · 09-04-2009, 02:07 PM

Some manufacturers will use stock disc blanks and drill or knee mill (slot) them. These metals are not supposed to be used for those aggressive applications and have a tendancy to crack or break under all the force with a compromised geometry. Basically if they start cutting holes or slots in the thing, you want to make sure they are using strong metals to reinforce the structure to withstand the hard clamping force of the calipers even with material removed.

Also, when you have a two piece rotor, it is just one more part to go wrong. You need to make sure the manufacturer has confronted the issues when you deal with screw on brake centers.

From the manufacturer site, "Alloyed iron formula adds strength and heat resistance. Heat treating further improves rotor performance for a more uniform and stabilized microstructure."

Center rotor hat mounting, "Exclusive full floating design with 10.9 grade alloyed hardware. Hardware is DACRO coated and crimp locking. DACRO is highly corrosion resistant and provides a film for easier movement between the hat and rotor ring as disc expands and contracts and the crimp design provides positive engagement without rattling or torque loss at temperature."

wstar · 09-04-2009, 03:00 PM

Those ones at racingbrake linked above look pretty good. However they don't seem to be actually available. The Slotted fronts say 6-8 weeks to ship, the open slotted fronts are "unavailable", and the rears are listed as 12-16 weeks out (holy crap that's 3-4 months).

Endgame · 09-04-2009, 03:02 PM

O.K. So for these Racing Brake rotors, as per their website, these appear to be good quality. Yes?

Sorry, I super multitasking today....

09-04-2009, 10:20 AM	#38 (permalink)
Equinox Track Member Join Date: Jul 2009 Location: Beaumont, TX Posts: 685 Drives: 06 Porsche Carrera S Rep Power: 18	this seems like an easy enough product to make, I wonder how hard it would be to take up this idea and make my own :P Maybe offer black, red, and blue anodized centers __________________ Check out my Albums '13 Subaru WRX STi \| '06 Porsche 911 Carrera S (SOLD) \| '96 Mazda RX-7 6.0L V8 RHD (SOLD) \| '09 Nissan Nismo #0058 (SOLD)

09-04-2009, 10:25 AM	#39 (permalink)
NIZMOZ Track Member Join Date: Nov 2008 Location: San Antonio, TX Posts: 634 Drives: 07 NISMO 350Z SA M6 Rep Power: 491	2-Pc Lightweight Rotors for Akebono Brakes - MyG37 2 Piece rotors..... __________________ SOLD: 2007 NISMO 350Z #0044 Silver Alloy New DD: 2010 Titan Pro4X CC

09-04-2009, 10:30 AM	#40 (permalink)
Equinox Track Member Join Date: Jul 2009 Location: Beaumont, TX Posts: 685 Drives: 06 Porsche Carrera S Rep Power: 18	The good news keeps rolling in - I found these for our stock calipers as well - they are two peice forged aluminum alloy hats, just like the ones you linked Nismoz, but these seem a little more aggressive 370Z (Sport) - RacingBrake.com 19 lbs compared to 30 lbs. If my rims weighed 30 lbs I sure as hell would be happy with buying lighter 19lb wheels. edit - apparently they are the same company as the picture posted in Nismoz link - but the rotor looks different in the link I posted. Hm. __________________ Check out my Albums '13 Subaru WRX STi \| '06 Porsche 911 Carrera S (SOLD) \| '96 Mazda RX-7 6.0L V8 RHD (SOLD) \| '09 Nissan Nismo #0058 (SOLD) Last edited by Equinox; 09-04-2009 at 10:52 AM.

09-04-2009, 02:07 PM	#43 (permalink)
Equinox Track Member Join Date: Jul 2009 Location: Beaumont, TX Posts: 685 Drives: 06 Porsche Carrera S Rep Power: 18	Some manufacturers will use stock disc blanks and drill or knee mill (slot) them. These metals are not supposed to be used for those aggressive applications and have a tendancy to crack or break under all the force with a compromised geometry. Basically if they start cutting holes or slots in the thing, you want to make sure they are using strong metals to reinforce the structure to withstand the hard clamping force of the calipers even with material removed. Also, when you have a two piece rotor, it is just one more part to go wrong. You need to make sure the manufacturer has confronted the issues when you deal with screw on brake centers. From the manufacturer site, "Alloyed iron formula adds strength and heat resistance. Heat treating further improves rotor performance for a more uniform and stabilized microstructure." Center rotor hat mounting, "Exclusive full floating design with 10.9 grade alloyed hardware. Hardware is DACRO coated and crimp locking. DACRO is highly corrosion resistant and provides a film for easier movement between the hat and rotor ring as disc expands and contracts and the crimp design provides positive engagement without rattling or torque loss at temperature." __________________ Check out my Albums '13 Subaru WRX STi \| '06 Porsche 911 Carrera S (SOLD) \| '96 Mazda RX-7 6.0L V8 RHD (SOLD) \| '09 Nissan Nismo #0058 (SOLD)

09-04-2009, 03:00 PM	#44 (permalink)
wstar A True Z Fanatic Join Date: Mar 2009 Location: Houston, TX Posts: 4,024 Drives: too slow Rep Power: 3594	Those ones at racingbrake linked above look pretty good. However they don't seem to be actually available. The Slotted fronts say 6-8 weeks to ship, the open slotted fronts are "unavailable", and the rears are listed as 12-16 weeks out (holy crap that's 3-4 months). __________________ 7AT Track Car! Journal thread / Car setup details

09-01-2009, 06:37 AM	#31 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7251	I'd be on board for this too as i was looking for some before i bought the stoptechs after i smoked the stock ones

09-03-2009, 04:58 PM	#32 (permalink)
henryv007 Base Member Join Date: Jul 2009 Location: San Juan Islands Posts: 29 Drives: 2009 370z Nismo Rep Power: 16	I may be all wet here but Stop Tech and Stillen do list cross drilled and slotted rotors for our cars, although they all appear to be 1 pc. like the stock. Am I right that the G37 rotors are the same and will fit the 370z as well? If so its worth looking through listings for those cars as well. Any thoughts as to 1 pc. and 2 pc, one being that much betetr than the other? Im new here so sorry for jumping in with a dumb question, but inquiring minds need to know!

09-03-2009, 05:10 PM	#33 (permalink)
Endgame A True Z Fanatic Join Date: Nov 2008 Location: Phoenix Posts: 1,613 Drives: Nothing Now! Rep Power: 224	actually, good question henryv007. what is the difference between a one piece and two piece rotor performance wise?

09-03-2009, 05:27 PM	#34 (permalink)
import111 Track Member Join Date: Feb 2009 Location: Tucson, AZ. Posts: 622 Drives: 09 Nissan 370Z Rep Power: 191	differences: 1. A 2 piece rotor usually uses an aluminum center (hat) which transfers less heat to the wheel, and there for, wheel bearings and other parts. 2. Because of that aluminum hat listed above, 2 piece rotors weigh less, which lightens the car as a whole, lightens the front (which is good if the front of the car is the heavier part), and gives the brake pads less weight to clamp onto which in turn should make for shorter stopping distance (if the tires can manage). 3. From what I have seen in 2 piece rotors, the cooling veins are better designed to evacuate heat.

09-03-2009, 06:57 PM	#36 (permalink)
Endgame A True Z Fanatic Join Date: Nov 2008 Location: Phoenix Posts: 1,613 Drives: Nothing Now! Rep Power: 224	that is what i figured; just wanted confirmation. THX!!!

09-04-2009, 01:18 PM	#41 (permalink)
Z1Performance Base Member Join Date: Aug 2009 Location: St. James, NY Posts: 237 Drives: 350Z Rep Power: 16	Weight is all fine and well, but you also need to look at the metallurgy of the disks, and, the mounting that the hat uses. There are many variables to consider

09-04-2009, 01:27 PM	#42 (permalink)
Endgame A True Z Fanatic Join Date: Nov 2008 Location: Phoenix Posts: 1,613 Drives: Nothing Now! Rep Power: 224	Why are those important??

09-04-2009, 03:02 PM	#45 (permalink)
Endgame A True Z Fanatic Join Date: Nov 2008 Location: Phoenix Posts: 1,613 Drives: Nothing Now! Rep Power: 224	O.K. So for these Racing Brake rotors, as per their website, these appear to be good quality. Yes? Sorry, I super multitasking today....

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: Brake rotor replacement (front)	ChrisSlicks	DIY Section (Do-It-Yourself)	63	02-10-2017 09:19 AM
ROTORA CROSS DRILLED AND SLOTTED ROTORS for 370z Sport now available at AMPLIFIED	LOU@AMPLIFIED	Suspension/Brakes	11	06-23-2013 02:18 PM
Stop-Tech Drilled & Slotted Installed	Minicobra1	Brakes & Suspension	31	06-16-2010 10:03 PM
3 piece wheel?	tvfreakazoid	Wheels & Tires	11	03-11-2009 05:13 PM
2010 BMW Z4 Plays With Paint In Massive Art Piece	AK370Z	Other Vehicles	1	12-29-2008 06:47 PM