Swift springs review!!!!!

KaienZ34 · 05-03-2013, 12:43 PM

I thought mine did, but I had the bump stop in wrong. Fixed that and the are just as quiet as stock.

wheee! · 05-03-2013, 12:44 PM

Seems like all the issues people have been having are due to lack of attention to detail during the install process. Nothing but 'win' from mine....

onzedge · 05-03-2013, 12:54 PM

Quote:

Originally Posted by wheee!

Seems like all the issues people have been having are due to lack of attention to detail during the install process. Nothing but 'win' from mine....

I have zero problems, only smiles and giggles.

speedfreek · 05-03-2013, 01:05 PM

No noise coming from my springs. I will be installing my toe bolts tomorrow to fix the issue I am having with scrubbing the rears off. Picked up dremel bit #115 for the task. Hopefully all goes well.

kenchan · 05-03-2013, 01:10 PM

i run swifts on my other car which is my dd. drove all winter through salt and hardly washed.

unlike tein and tanabe springs where the paint started cracking off in one winter use, the swifts held up fine. the springs are wound very well to match the stock dampers too. i think this is the only spring manufacturer that actually tests the ride quality of the car.

the others (tein, tanabe, eibach to name a few) are like just eyeball the spring rate, should work.... and it doesnt.

ZMan8 · 05-03-2013, 01:11 PM

Quote:

Originally Posted by speedfreek

No noise coming from my springs. I will be installing my toe bolts tomorrow to fix the issue I am having with scrubbing the rears off. Picked up dremel bit #115 for the task. Hopefully all goes well.

KaienZ34 · 05-03-2013, 01:11 PM

I installed my spl rear camber arms but didn't need the spc toe bolts to get the rear back in spec. Now I just some front camber adjustment and i'll be good.

speedfreek · 05-03-2013, 01:18 PM

Quote:

Originally Posted by KaienZ34

I installed my spl rear camber arms but didn't need the spc toe bolts to get the rear back in spec. Now I just some front camber adjustment and i'll be good.

Well mine may be the tech at Firestone doesn't know what he is doing. But they said it is the best they could do to get it back in spec (which was 0.15 and 0.18 deg toe). When I got new tires installed last week at Nissan they said "our tech thinks he can get it in spec." I said, "can you guarantee that as in if you can't get it in spec I am not paying." They said "No." So I figure it would be best to go ahead and install the toe bolts and take it back to Firestone to get the toe dialed into 0 deg rather than to pay a shop $80 to try and get it in spec with the stock bolts. Right now I am only out $10 for drill bits and a couple hours tomorrow to do the install.

bmarcinczyk14 · 05-03-2013, 01:25 PM

Quote:

Originally Posted by wheee!

Seems like all the issues people have been having are due to lack of attention to detail during the install process. Nothing but 'win' from mine....

I brought mine back to the installer to try and fix the creaking noise, he even removed the suspected side again and greased the sleeve that's supposed to prevent the creaking noise. I got it back and at first I thought he fixed the problem, but after a day it started creaking again. It's not a biggie, it's only going up curbs slowly, normal driving I don't hear anything from them, so I think I'll just live with it.

ZMan8 · 05-03-2013, 01:26 PM

Quote:

Originally Posted by bmarcinczyk14

I brought mine back to the installer to try and fix the creaking noise, he even removed the suspected side again and greased the sleeve that's supposed to prevent the creaking noise. I got it back and at first I thought he fixed the problem, but after a day it started creaking again. It's not a biggie, it's only going up curbs slowly, normal driving I don't hear anything from them, so I think I'll just live with it.

Very strange it keeps doing that after several times of reinstalling it.

wheee! · 05-03-2013, 01:33 PM

Quote:

Originally Posted by speedfreek

Well mine may be the tech at Firestone doesn't know what he is doing. But they said it is the best they could do to get it back in spec (which was 0.15 and 0.18 deg toe). When I got new tires installed last week at Nissan they said "our tech thinks he can get it in spec." I said, "can you guarantee that as in if you can't get it in spec I am not paying." They said "No." So I figure it would be best to go ahead and install the toe bolts and take it back to Firestone to get the toe dialed into 0 deg rather than to pay a shop $80 to try and get it in spec with the stock bolts. Right now I am only out $10 for drill bits and a couple hours tomorrow to do the install.

You can always get the toe back to spec, but the camber will suffer or vice versa. You cannot get both back to spec without a camber kit and toe bolts... so either live with -2.8 camber or get a set of toe bolt and camber arms!

speedfreek · 05-03-2013, 01:48 PM

Quote:

Originally Posted by wheee!

You can always get the toe back to spec, but the camber will suffer or vice versa. You cannot get both back to spec without a camber kit and toe bolts... so either live with -2.8 camber or get a set of toe bolt and camber arms!

Rgr that. I already have the SPC rear camber arms on and the rear camber is 1.7 - 1.8 IRC. So toe bolts it is.

KaienZ34 · 05-03-2013, 01:50 PM

Quote:

Originally Posted by speedfreek

Well mine may be the tech at Firestone doesn't know what he is doing. But they said it is the best they could do to get it back in spec (which was 0.15 and 0.18 deg toe). When I got new tires installed last week at Nissan they said "our tech thinks he can get it in spec." I said, "can you guarantee that as in if you can't get it in spec I am not paying." They said "No." So I figure it would be best to go ahead and install the toe bolts and take it back to Firestone to get the toe dialed into 0 deg rather than to pay a shop $80 to try and get it in spec with the stock bolts. Right now I am only out $10 for drill bits and a couple hours tomorrow to do the install.

That's cool i'm not picking with you, I was just saying what mine looked like.

speedfreek · 05-03-2013, 01:53 PM

Quote:

Originally Posted by KaienZ34

That's cool i'm not picking with you, I was just saying what mine looked like.

No worries. Perhaps you are running more camber with your setup allowing your toe to be near 0.

KaienZ34 · 05-03-2013, 04:35 PM

I know it's been talked about before, but does anyone know if SPL is ever going to come out with a front camber kit?

05-03-2013, 12:43 PM	#1696 (permalink)
KaienZ34 A True Z Fanatic Join Date: Oct 2009 Location: LA. not L.a. Posts: 21,652 Drives: Z34 Tour/Sport Rep Power: 178	I thought mine did, but I had the bump stop in wrong. Fixed that and the are just as quiet as stock. __________________ *"These Violent Delights Have Violent Ends"* http://www.the370z.com/members/kaienz34-albums-z34.html

05-03-2013, 12:44 PM	#1697 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	Seems like all the issues people have been having are due to lack of attention to detail during the install process. Nothing but 'win' from mine.... __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

05-03-2013, 01:05 PM	#1699 (permalink)
speedfreek A True Z Fanatic Join Date: Feb 2012 Location: Huntsville,AL Posts: 1,724 Drives: '12 370Z PW 6sp Rep Power: 18	No noise coming from my springs. I will be installing my toe bolts tomorrow to fix the issue I am having with scrubbing the rears off. Picked up dremel bit #115 for the task. Hopefully all goes well. ZMan8 likes this. __________________ Tomei\|Berk\|Takeda\|ZSpeed\|Fortune Auto\|Swift\|Eibach\|SPL\|Carbotech\|Motul\|Powertrix\|Stillen\|Aerojacket\|Z1\|Forgestar\|Enkei\|Project Kics\|Nismo Ti\|Llumar speedfreek's journal

05-03-2013, 01:10 PM	#1700 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	i run swifts on my other car which is my dd. drove all winter through salt and hardly washed. unlike tein and tanabe springs where the paint started cracking off in one winter use, the swifts held up fine. the springs are wound very well to match the stock dampers too. i think this is the only spring manufacturer that actually tests the ride quality of the car. the others (tein, tanabe, eibach to name a few) are like just eyeball the spring rate, should work.... and it doesnt. KaienZ34 likes this.

05-03-2013, 01:11 PM	#1702 (permalink)
KaienZ34 A True Z Fanatic Join Date: Oct 2009 Location: LA. not L.a. Posts: 21,652 Drives: Z34 Tour/Sport Rep Power: 178	I installed my spl rear camber arms but didn't need the spc toe bolts to get the rear back in spec. Now I just some front camber adjustment and i'll be good. onzedge likes this. __________________ *"These Violent Delights Have Violent Ends"* http://www.the370z.com/members/kaienz34-albums-z34.html

05-03-2013, 04:35 PM	#1710 (permalink)
KaienZ34 A True Z Fanatic Join Date: Oct 2009 Location: LA. not L.a. Posts: 21,652 Drives: Z34 Tour/Sport Rep Power: 178	I know it's been talked about before, but does anyone know if SPL is ever going to come out with a front camber kit? __________________ *"These Violent Delights Have Violent Ends"* http://www.the370z.com/members/kaienz34-albums-z34.html Last edited by KaienZ34; 05-05-2013 at 01:30 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Swift Springs-- Nismo Review!!	JJ-NISMO	Brakes & Suspension	39	07-29-2014 08:59 AM
[WTB] Swift Springs	Beastmode	Parts for sale (Private Classifieds)	1	09-13-2011 05:46 PM
BC ERs with Swift Springs and RA Valving REVIEW / (Picture Heavy)	Mozen	Brakes & Suspension	31	05-24-2011 11:46 AM
WTB: Swift or H&R Springs	Mr&Mrs	Wanted	5	04-26-2011 11:51 PM
Swift Springs	Justin1686	North East Region	10	02-24-2011 07:58 PM