GTSPEC 6 Point Ladder Brace

Jeffblue · 09-24-2010, 12:50 PM

Vipor is on it today.

RCZ · 09-24-2010, 12:52 PM

I have about a finger gap all around. If I spin my exhaust bolts so that the bolt is sticking towards the ground I scrape on everything...and thats like maybe an inch to 1.5inch lower than the rest of the car. If I drive around with tires on trackday pressure settings, I scrape going into my garage, at 35psi, no scrape.

Jeffblue · 09-24-2010, 12:58 PM

1 finger wheel gap? do you know in inches how much lower you are? i am going to get coilovers and drop an inch, so i'm just curious, will i have clearance issues with this brace?

jnaut · 09-24-2010, 01:11 PM

Quote:

Originally Posted by Jeffblue

1 finger wheel gap? do you know in inches how much lower you are? i am going to get coilovers and drop an inch, so i'm just curious, will i have clearance issues with this brace?

have fun on speed bumps

Jeffblue · 09-24-2010, 01:30 PM

with the brace or in general? I hate how they made this car so low, but with so much wheel gap. they make it such a dilemma to lower the car.

spearfish25 · 09-24-2010, 01:54 PM

Quote:

Originally Posted by Jeffblue

with the brace or in general? I hate how they made this car so low, but with so much wheel gap. they make it such a dilemma to lower the car.

20" rims?

Jeffblue · 09-24-2010, 02:00 PM

Quote:

Originally Posted by spearfish25

20" rims?

what about them? Mine are 19"

vipor · 09-24-2010, 02:42 PM

Quote:

Originally Posted by daleks

So it looks like the 4-point brace blocks the front jack point. Oops...

It does

I'm gonna build some 2x10 ramps before my next oil change so I can get my floor jack under my car more easily..

daleks · 09-24-2010, 03:28 PM

Quote:

Originally Posted by vipor

It does

I'm gonna build some 2x10 ramps before my next oil change so I can get my floor jack under my car more easily..

I recommend 2x12's. I have a pair of 3' segments with 45 degree mitre cuts at the end I wedge under the front tires before pulling forward and jacking up my front end. The true size of a 2x10 is 9 1/4", which isn't wide enough to fully span a 245mm (9.65 inches) tire. I pushed my compound mitre saw (dual sliding 10") to the limit though doing a cut like that on a 2x12 (11 1/4").

m4a1mustang · 09-24-2010, 03:29 PM

Quote:

Originally Posted by daleks

I recommend 2x12's. I have a pair of 3' segments with 45 degree mitre cuts at the end I wedge under the front tires before pulling forward and jacking up my front end. The true size of a 2x10 is 9 1/4", which isn't wide enough to fully span a 245mm (9.65 inches) tire. I pushed my compound mitre saw (dual sliding 10") to the limit though doing a cut like that on a 2x12 (11 1/4").

They were so helpful with my Z. Saved me a few hundred bucks on buying a long-neck, low profile jack.

vipor · 09-24-2010, 04:56 PM

/subscribe. thanks

spearfish25 · 09-24-2010, 05:32 PM

Quote:

Originally Posted by Jeffblue

what about them? Mine are 19"

You wanted less wheel gap without dropping the car on coilovers. Bigger rims is the answer. Hell, get 22"s!

Jeffblue · 09-24-2010, 05:41 PM

Quote:

Originally Posted by spearfish25

You wanted less wheel gap without dropping the car on coilovers. Bigger rims is the answer. Hell, get 22"s!

hahah, yea you gotta think outside the Box sometimes!

Jamaica · 09-24-2010, 06:32 PM

Quote:

Originally Posted by Jeffblue

hahah, yea you gotta think outside the Box sometimes!

dont hate man his pimpin

Chris_1 · 09-25-2010, 01:47 AM

Still wish it was orange lol.

09-24-2010, 04:56 PM	#41 (permalink)
vipor A True Z Fanatic Join Date: Aug 2009 Location: Euless, TX [ DFW ] Age: 42 Posts: 13,531 Drives: Nismo 09-0183 QAB Rep Power: 49	/subscribe. thanks __________________ 2009 NISMO # 0193 \| QAB \| Albums! \| 05.04.10 (Dynojet) 291.94hp/248.28tq Oil Cooler (DIY) \| Custom Headlights \| GTSPEC Braces \| F.I. Long Tube Headers

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: GT-SPEC 4-Point Ladder Bar	Equinox	DIY Section (Do-It-Yourself)	7	07-14-2012 06:45 AM
GTSPEC Front 6 Point Subframe Brace Test Vehicle Needed	gtspec-ny	North East Region	11	09-01-2010 11:16 AM
IDIOT Driver Vs. Ladder User	AK370Z	The Lounge (Off Topic)	12	03-08-2010 10:09 PM
DIY: GTSPEC 4-Point Ladder Brace	M.Bonanni	DIY Section (Do-It-Yourself)	8	07-29-2009 02:44 PM

09-24-2010, 12:50 PM	#31 (permalink)
Jeffblue A True Z Fanatic Join Date: Dec 2009 Location: NY Age: 36 Posts: 9,192 Drives: Z32TT & 335xi Coupe Rep Power: 37	Vipor is on it today.

09-24-2010, 12:52 PM	#32 (permalink)
RCZ A True Z Fanatic Join Date: Nov 2008 Location: Miami Posts: 6,403 Drives: '09 370Z Rep Power: 1119	I have about a finger gap all around. If I spin my exhaust bolts so that the bolt is sticking towards the ground I scrape on everything...and thats like maybe an inch to 1.5inch lower than the rest of the car. If I drive around with tires on trackday pressure settings, I scrape going into my garage, at 35psi, no scrape.

09-24-2010, 12:58 PM	#33 (permalink)
Jeffblue A True Z Fanatic Join Date: Dec 2009 Location: NY Age: 36 Posts: 9,192 Drives: Z32TT & 335xi Coupe Rep Power: 37	1 finger wheel gap? do you know in inches how much lower you are? i am going to get coilovers and drop an inch, so i'm just curious, will i have clearance issues with this brace?

09-24-2010, 01:30 PM	#35 (permalink)
Jeffblue A True Z Fanatic Join Date: Dec 2009 Location: NY Age: 36 Posts: 9,192 Drives: Z32TT & 335xi Coupe Rep Power: 37	with the brace or in general? I hate how they made this car so low, but with so much wheel gap. they make it such a dilemma to lower the car.

09-25-2010, 01:47 AM	#45 (permalink)
Chris_1 Track Member Join Date: Mar 2010 Location: Statewide Posts: 838 Drives: Nissan 370Z Roadster Rep Power: 16	Still wish it was orange lol.