My Relentless Autosports floating rotors

Vegitto-kun · 08-07-2010, 05:43 AM

I want these so much but no money makes this a very sad davy haha

Mozen · 08-07-2010, 05:53 AM

These are very nice. Ill be ordering a set of front 2pc Floating for track use later in the year. Just got my BC ERs in with RA custom valving and swift springs which ill post pics of later when i can get them taken.

As far as price Triple i cant remember how much the full kit is since im only looking at getting the fronts. PM Scott. He also has a "spacer kit" or something that will allow you to fit a thicker rotor in the rear if you so choose but dont quote me. It was just one of the many things we had talked about on the phone. So far RA has the best options (i think) for after-market rotors for your sport brakes.

Jordo! · 08-07-2010, 07:11 AM

Are these strictly for the track? I thought full floating rotors tended to be fairly noisy at low speeds...

Do you guys make semi-floating rotors too?

Scott @ RA · 08-07-2010, 02:19 PM

Quote:

Originally Posted by Jordo!

Are these strictly for the track?

Although the rotors are designed for brutal track use, they are also street suitable.

Quote:

Originally Posted by Jordo!

I thought full floating rotors tended to be fairly noisy at low speeds...

The option of the full floating rotors can tend to make a little rattle noise when you are off the brakes at low speeds, but most don't seem to mind the noise givin all the benefits of a full floating rotor.

Quote:

Originally Posted by Jordo!

Do you guys make semi-floating rotors too?

You have the option of ordering the rotors as full floating or non-floating.

gpa7pk · 09-10-2010, 04:53 PM

Finally got around to installing my Relentless Autosports two piece floating front rotors and the custom valved BC ER coilovers with Swift springs. I will working on the rear shortly, but I did notice Zat_Zuma has installed his rear RA two piece rotors mentioned a another thread.

I used exisiting DIY's from this forum and the Nissan service manual to assist in the install. I don't think anything needs to be added except use the right tools and make sure your Z is properly and safely supported when working on the suspension. Some of the torque requirements are up tp 120 ft/lbs and breaking some the bolts loose remind me dreaded HFC bolt - torqued by Nissan to some ridiculously high but not required value.

When I get the rears done I will go for a test drive and then replace the brake pads and install the SS brake lines.

The Stillen sways will be installed prior to the first test drive.

A few pictures:

Zat_Zuma · 09-10-2010, 05:42 PM

Quote:

Originally Posted by gpa7pk

Finally got around to installing my Relentless Autosports two piece floating front rotors and the custom valved BC ER coilovers with Swift springs. I will working on the rear shortly, but I did notice Zat_Zuma has installed his rear RA two piece rotors mentioned a another thread.

Pm me for some tips

Scott @ RA · 09-11-2010, 12:41 PM

Quote:

Originally Posted by gpa7pk

Finally got around to installing my Relentless Autosports two piece floating front rotors and the custom valved BC ER coilovers with Swift springs. I will working on the rear shortly, but I did notice Zat_Zuma has installed his rear RA two piece rotors mentioned a another thread.

I used exisiting DIY's from this forum and the Nissan service manual to assist in the install. I don't think anything needs to be added except use the right tools and make sure your Z is properly and safely supported when working on the suspension. Some of the torque requirements are up tp 120 ft/lbs and breaking some the bolts loose remind me dreaded HFC bolt - torqued by Nissan to some ridiculously high but not required value.

When I get the rears done I will go for a test drive and then replace the brake pads and install the SS brake lines.

The Stillen sways will be installed prior to the first test drive.

A few pictures:

Great pictures Glen, Thanks for posting them...

ChrisSlicks · 09-29-2010, 04:37 PM

Nice looking setup. Looking forward to some track performance review.

KillBill · 10-16-2010, 10:13 PM

Has anybody weighed the stock rears with the two piece...a few people asked but there was no response.

gpa7pk · 10-17-2010, 08:18 AM

Earlier in this thread I posted the front and rear rotor weight and savings over OEM rotors; which is right at 10 lbs per corner.

KillBill · 10-17-2010, 06:30 PM

The rears are definately not going to be ten pounds lighter per side....Has anybody actually gotten out a scale and weighed the stock vs. the rears?

ChrisSlicks · 10-17-2010, 07:32 PM

Quote:

Originally Posted by KillBill

The rears are definately not going to be ten pounds lighter per side....Has anybody actually gotten out a scale and weighed the stock vs. the rears?

If they are aluminum hats on the rear then yes they will be 10 pounds lighter if not more.

gpa7pk · 10-17-2010, 08:31 PM

Quote:

Originally Posted by ChrisSlicks

If they are aluminum hats on the rear then yes they will be 10 pounds lighter if not more.

The RA rotors have aluminum hats and I weighed them on a plain old house scale. They are just a bit over 10 lbs lighter per rotor.

Q8y_drifter · 10-18-2010, 07:36 AM

Quote:

Originally Posted by gpa7pk

The RA rotors have aluminum hats and I weighed them on a plain old house scale. They are just a bit over 10 lbs lighter per rotor.

for the rears??

Kirkster · 10-18-2010, 08:16 AM

How does the car feel now???

Did the brake line bracket that is attached to the body of the shock holding the brake line come with the shocks or did you have to take it off the old shock???

I am going to hit Scott up for this setup when I get back in country next month for my roadster.

08-07-2010, 05:53 AM	#17 (permalink)
Mozen Track Member Join Date: Jun 2010 Location: Newport News, VA Posts: 820 Drives: Nissan 370z PW M6 Rep Power: 18	These are very nice. Ill be ordering a set of front 2pc Floating for track use later in the year. Just got my BC ERs in with RA custom valving and swift springs which ill post pics of later when i can get them taken. As far as price Triple i cant remember how much the full kit is since im only looking at getting the fronts. PM Scott. He also has a "spacer kit" or something that will allow you to fit a thicker rotor in the rear if you so choose but dont quote me. It was just one of the many things we had talked about on the phone. So far RA has the best options (i think) for after-market rotors for your sport brakes. __________________ PW 370z \| AEM \| MISHIMOTO \| ARK PERFORMANCE \| WHITELINE \| NISMO \| STILLEN \| FORGESTAR \| BC RACING \| AMS \| NON STOP TUNING \| CARBONETICS LSD \| 4 Point DOM 1.75" SCCA Spec Roll Bar + Harness Bar CHECK OUT MY BUILD THREAD HERE

08-07-2010, 07:11 AM	#18 (permalink)
Jordo! A True Z Fanatic Join Date: May 2010 Location: nirvana Posts: 6,394 Drives: 2023 NATM Rep Power: 418	Are these strictly for the track? I thought full floating rotors tended to be fairly noisy at low speeds... Do you guys make semi-floating rotors too? __________________ Enjoy it. Destroy it.

09-29-2010, 04:37 PM	#23 (permalink)
ChrisSlicks A True Z Fanatic Join Date: Mar 2009 Location: North East Posts: 6,203 Drives: 09 370Z Sport M6 Rep Power: 653	Nice looking setup. Looking forward to some track performance review. __________________ Hotchkis ARB \| Stillen CAI \| Art Pipes \| Berk CBE \| Stillen AP Racing Brakes \| AE Performance Oil Cooler \| BC Racing ER Coilovers \| Doran Control Arms

10-18-2010, 08:16 AM	#30 (permalink)
Kirkster A True Z Fanatic Join Date: Dec 2008 Location: Peoples Republic of MD Posts: 1,792 Drives: Roadster of DOOM Rep Power: 19	How does the car feel now??? Did the brake line bracket that is attached to the body of the shock holding the brake line come with the shocks or did you have to take it off the old shock??? I am going to hit Scott up for this setup when I get back in country next month for my roadster. __________________ Powertrain Warranty voided on 5/14/2011 Mod List:GTM Supercharger,SmartTop module, Oil Cooler, GT-R Start button, Nismo Exhaust, BC Racing ER Coilovers, Backup Camara For eastwest:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Relentless Autosports: GROUP BUY / 2 piece F&R rotors set for the Akebono brake kit	Scott @ RA	Group Buys	120	10-09-2014 12:42 PM
Relentless Autosports: Your source for all Akebono brake kits, options, and supplies	Scott @ RA	Suspension/Brakes	1	07-02-2010 07:55 PM
Rotors	Ty Weezy	Brakes & Suspension	5	06-19-2010 01:56 PM
Relentless Autosports 2 Peice Brakes	Equinox	Brakes & Suspension	11	04-12-2010 05:03 AM

08-07-2010, 05:43 AM	#16 (permalink)
Vegitto-kun A True Z Fanatic Join Date: Feb 2010 Location: USA Posts: 2,011 Drives: 09 370Z Rep Power: 262	I want these so much but no money makes this a very sad davy haha

10-16-2010, 10:13 PM	#24 (permalink)
KillBill Base Member Join Date: Jul 2009 Location: San Bernardino Posts: 86 Drives: 08-G37S Rep Power: 16	Has anybody weighed the stock rears with the two piece...a few people asked but there was no response.

10-17-2010, 08:18 AM	#25 (permalink)
gpa7pk Base Member Join Date: Apr 2009 Location: Texas Posts: 135 Drives: 1959 Triumph TR3A Rep Power: 16	Earlier in this thread I posted the front and rear rotor weight and savings over OEM rotors; which is right at 10 lbs per corner.

10-17-2010, 06:30 PM	#26 (permalink)
KillBill Base Member Join Date: Jul 2009 Location: San Bernardino Posts: 86 Drives: 08-G37S Rep Power: 16	The rears are definately not going to be ten pounds lighter per side....Has anybody actually gotten out a scale and weighed the stock vs. the rears?