Best springs...

tbonesteak · 06-11-2010, 12:12 PM

Quote:

Originally Posted by wishihadnav

its probably not the springs that caused the bounce but shocks/struts which prematurely wear over time..

Not true. I swapped out the eibachs with neuspeed/h&r and the ride was perfect again on same shocks. Eibachs are known to have this problem (atleast in the honda/acura community) and i was one of the test dummies that found out the hard way.

RomRox · 06-11-2010, 01:29 PM

I've had a very good experience with H&R's with my S2000 with stock shocks. Drop wasnt extreme however, <1" drop.

I was leaning towards Eibach with the 370, but with the reports of the springs going/feeling soft after some time, I've decided to drop the car properly and go with KW coilovers. I originally was going to go just KW V1's with just height adjustibility, but in instead of taking my chances with not liking the ride dampening, decided to go KW V3's.

I hadn't considered H&R's for the 370 since the the drop just looks too extreme for the roads up here in Canada. I'd probably be scraping all over the place!

wishihadnav · 06-11-2010, 01:32 PM

Quote:

Originally Posted by tbonesteak

Not true. I swapped out the eibachs with neuspeed/h&r and the ride was perfect again on same shocks. Eibachs are known to have this problem (atleast in the honda/acura community) and i was one of the test dummies that found out the hard way.

i've had eibachs on a few of my cars and no bounce..the pro-kits..they ride like stock at least in my experience..just not enough drop..

kenchan · 06-11-2010, 02:57 PM

ironically the neuspeeds i installed in my prelude many many years ago was bouncy as hell and undulated under moderate driving conditions. this was on a car with less than 3k miles. quickly swapped them out for TEIN HA's which were considered new and cool at the time.

you really need to look at the spring rates, linear or progressive, and amount of drop, amount of bumpstop you cut or replace, and your wheel's offsets (wheel rate) to get a sense of what to expect.

on that note (i dont plan on lowering my Z with lowering springs but) what is the spring rates of the stock springs? that is where i would start the search if i was looking for springs.

wasti · 06-11-2010, 05:24 PM

... because some of you asked about a picture from a z with eibach and stock wheels. here it is.

kevr6 · 06-11-2010, 09:45 PM

Quote:

Originally Posted by kenchan

ironically the neuspeeds i installed in my prelude many many years ago was bouncy as hell and undulated under moderate driving conditions. this was on a car with less than 3k miles. quickly swapped them out for TEIN HA's which were considered new and cool at the time.

you really need to look at the spring rates, linear or progressive, and amount of drop, amount of bumpstop you cut or replace, and your wheel's offsets (wheel rate) to get a sense of what to expect.

on that note (i dont plan on lowering my Z with lowering springs but) what is the spring rates of the stock springs? that is where i would start the search if i was looking for springs.

I thought Eibach made Nuespeed's springs!!

tbonesteak · 06-12-2010, 01:01 AM

no....h&r and neuspeed are the same company, but neuspeed doesnt make parts for nissans.

speedworks · 06-12-2010, 03:08 PM

^^^"h&r and neuspeed are the same company"

Where did you hear this?

tjlazer · 06-12-2010, 05:06 PM

I think you are wanting to go with a Linear spring on the 370Z. I am going to try RS*R Linear springs Ti2000 from the 350Z, they claim a .6" drop and Front Stiffness: 6.2kg/mm (345lb) Rear Stiffness: 7.5kg/mm (417lb) so hopefully they do well! I'll let you all know soon.

kenchan · 06-12-2010, 10:03 PM

yah, H&R oems to Neuspeed. the neuspeeds for the prelude was made by H&R at least.

tbonesteak · 06-12-2010, 11:06 PM

Quote:

Originally Posted by speedworks

^^^"h&r and neuspeed are the same company"

Where did you hear this?

Just something i've known from being in the community for 10+ years now. It's common knowledge that most people are aware of. Feel free to research if you're doubtful

speedworks · 06-12-2010, 11:10 PM

I used to own a speed shop, and distributed both of those products, and they came from different places - different owners.

Actually, I was commenting that they were the same company, which I don't think is true. Sure maybe Neuspeed has H&R make their springs, but they aren't the same company, which is what I was questioning. I did a quick search and found nothing that said they are the same company.

kevr6 · 06-12-2010, 11:31 PM

Quote:

Originally Posted by speedworks

^^^"h&r and neuspeed are the same company"

Where did you hear this?

H&R is a German company and Neuspeed springs are advertised as being made in Germany. I just knew that Neuspeed did not produce their own springs and couldn't remember since the last time I looked into it was in 1998.

BTW, They are not the same company.

tbonesteak · 06-13-2010, 05:43 PM

damn....maybe i'm off then. but they were some how affiliated for sure in the past. Like kenchan said, i remember back in the days when they were manufacturing each others' parts even if it was for a little while. Thanks for the clarification.

corner3garage · 06-14-2010, 01:33 PM

tanabe's and the eibachs will give you the most bang for the buck. Both companies have good quality as well

06-12-2010, 05:06 PM	#24 (permalink)
tjlazer A True Z Fanatic Join Date: Dec 2009 Location: Tacoma Age: 52 Posts: 2,496 Drives: Z34, R35 Rep Power: 19	I think you are wanting to go with a Linear spring on the 370Z. I am going to try RS*R Linear springs Ti2000 from the 350Z, they claim a .6" drop and Front Stiffness: 6.2kg/mm (345lb) Rear Stiffness: 7.5kg/mm (417lb) so hopefully they do well! I'll let you all know soon. __________________ 2009 370Z Monterey Blue,Nismo Conversion,RE-11's, K&N Typhoon intakes,Blue Kickplates,Homelink,FI 18" CBE,ERZ HFCs,Hotchkis sways, Swift Spec-R, EVO-R Highwing, UPREV

06-12-2010, 11:10 PM	#27 (permalink)
speedworks Track Member Join Date: Jan 2009 Location: Boston, MA Posts: 550 Drives: PW purchased 01/09 Rep Power: 17	I used to own a speed shop, and distributed both of those products, and they came from different places - different owners. Actually, I was commenting that they were the same company, which I don't think is true. Sure maybe Neuspeed has H&R make their springs, but they aren't the same company, which is what I was questioning. I did a quick search and found nothing that said they are the same company. Last edited by speedworks; 06-12-2010 at 11:19 PM.

06-14-2010, 01:33 PM	#30 (permalink)
corner3garage The370Z.com Sponsor Join Date: Oct 2009 Location: Laguna Hills, CA Posts: 9,879 Drives: 240sx, 350z, 370z Rep Power: 35	tanabe's and the eibachs will give you the most bang for the buck. Both companies have good quality as well __________________ Corner3motorsports.com

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
RS-R springs?	GTRFAN	Brakes & Suspension	74	03-08-2012 09:41 AM
H&R Springs Anyone ?	Zeester	Brakes & Suspension	88	09-30-2010 05:11 AM
Should i get springs or coilovers (help)	xbigb4ller69z	Brakes & Suspension	5	08-14-2010 02:14 PM
H&R Lowering Springs?	CBRich	Brakes & Suspension	8	03-01-2010 01:35 PM
h&r springs	discorpio	Brakes & Suspension	11	01-11-2010 05:06 PM

06-11-2010, 01:29 PM	#17 (permalink)
RomRox Base Member Join Date: May 2010 Location: Edmonton, Alberta Posts: 110 Drives: 10 Nissan 370Z MB M6 Rep Power: 15	I've had a very good experience with H&R's with my S2000 with stock shocks. Drop wasnt extreme however, <1" drop. I was leaning towards Eibach with the 370, but with the reports of the springs going/feeling soft after some time, I've decided to drop the car properly and go with KW coilovers. I originally was going to go just KW V1's with just height adjustibility, but in instead of taking my chances with not liking the ride dampening, decided to go KW V3's. I hadn't considered H&R's for the 370 since the the drop just looks too extreme for the roads up here in Canada. I'd probably be scraping all over the place!

06-11-2010, 02:57 PM	#19 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	ironically the neuspeeds i installed in my prelude many many years ago was bouncy as hell and undulated under moderate driving conditions. this was on a car with less than 3k miles. quickly swapped them out for TEIN HA's which were considered new and cool at the time. you really need to look at the spring rates, linear or progressive, and amount of drop, amount of bumpstop you cut or replace, and your wheel's offsets (wheel rate) to get a sense of what to expect. on that note (i dont plan on lowering my Z with lowering springs but) what is the spring rates of the stock springs? that is where i would start the search if i was looking for springs.

06-12-2010, 01:01 AM	#22 (permalink)
tbonesteak Track Member Join Date: Mar 2009 Location: Socal Posts: 914 Drives: MY09 MB 6MT Rep Power: 375	no....h&r and neuspeed are the same company, but neuspeed doesnt make parts for nissans.

06-12-2010, 03:08 PM	#23 (permalink)
speedworks Track Member Join Date: Jan 2009 Location: Boston, MA Posts: 550 Drives: PW purchased 01/09 Rep Power: 17	^^^"h&r and neuspeed are the same company" Where did you hear this?

06-12-2010, 10:03 PM	#25 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	yah, H&R oems to Neuspeed. the neuspeeds for the prelude was made by H&R at least.

06-13-2010, 05:43 PM	#29 (permalink)
tbonesteak Track Member Join Date: Mar 2009 Location: Socal Posts: 914 Drives: MY09 MB 6MT Rep Power: 375	damn....maybe i'm off then. but they were some how affiliated for sure in the past. Like kenchan said, i remember back in the days when they were manufacturing each others' parts even if it was for a little while. Thanks for the clarification.