Bell Raceworks Diff Brace Install

RN SHARK · 01-31-2019, 12:45 PM

Quote:

Originally Posted by Spooler

Mine just showed up last night. I knew I should have waited. Dang it. No worries, I will make Chicken soup out of Chicken poop.

Kinda like how I just bought a Z1 radiator cap from someone one the forum, only to receive it and realize it is the same kPa as the stock one. 137. My bad. I should’ve looked closer.

JTM88 · 01-31-2019, 01:20 PM

I'm glad I waited, that's pretty crappy of Z1 to remove reviews.

Spoiler · 01-31-2019, 02:55 PM

Quote:

Originally Posted by Hotrodz

When in doubt pull out! LMAO

Sent from my SM-G965U using Tapatalk

..

Rusty · 01-31-2019, 04:42 PM

This is the review that I'm posting again.

If you have exhaust like FI that are close to the diff. This brace won't fit unless you trim about 1 3/8" on the corner of the brace. The other problem is that the upper mounting hole does not line up with the hole in the sub-frame. It's off by a bolt hole diameter. They say to loosen the diff bolting up to the diff so that you can move the diff around and get the holes to line up. Problem is if you have a solid bushing like SPL. When tightening the diff bolting back down. This will put stress on the bolting that you don't need. If you have the stock rubber bushing. you might get away with it.

The other thing that I noticed. There is weld beads on both sides of the bends of the brace. It looks like when bending the metal to shape. The metal cracked at the bends. So they welded over the cracks to hide them.

Rusty

Rusty · 01-31-2019, 04:45 PM

Just seen this on the Z1 website.

"Thank you for your review. It has been submitted to the store owner for approval and should appear shortly."

Spoiler · 01-31-2019, 07:21 PM

All you can do is be honest... and sounds like you were...

2011 Nismo#91 · 02-01-2019, 09:32 AM

You won't find a single bad review at Z1 or Stillen or any small vendor, their products are always excellent every time.

Except when there not and those don't get approved.

JARblue · 02-03-2019, 06:15 AM

Z1 routinely deletes negative reviews from what I can tell. I've had a couple deleted and know several others that have experienced the same thing.

Bswanny · 02-03-2019, 11:05 AM

Personally I have only had poor quality parts from Z1 and am told to shut up because everyone thinks Z1 is god. I feel bad for you the brace didn't work but when I read it's a direct fit for the 350Z and you need to unbolt the diff for the 370Z, I knew corners were cut. They used the same piece for two different applications to save costs. Shame

Sent from my SAMSUNG-SM-G930A using Tapatalk

NeverBoneStck · 02-03-2019, 01:10 PM

Quote:

Originally Posted by Rusty

Yep!

I am bmpboosted and it is on Instagram. I posted the picks plus everything else I post under bmpboosted and their reply is still there. Not sure what Rusty is looking up.

cv129 · 02-03-2019, 01:22 PM

Quote:

Originally Posted by NeverBoneStck

I am bmpboosted and it is on Instagram. I posted the picks plus everything else I post under bmpboosted and their reply is still there. Not sure what Rusty is looking up.

Rusty just meant that he himself is not on Instagram, not disputing your post, lol

NeverBoneStck · 02-03-2019, 02:05 PM

Quote:

Originally Posted by cv129

Rusty just meant that he himself is not on Instagram, not disputing your post, lol

My bad!! Sorry Rusty.

bpchaos · 02-05-2019, 08:24 PM

Bell Raceworks makes a slightly different brace for those with stock diff covers. I'll let you all know how that one fits (if it does) when I install it.

cv129 · 02-05-2019, 09:14 PM

Quote:

Originally Posted by bpchaos

Bell Raceworks makes a slightly different brace for those with stock diff covers. I'll let you all know how that one fits (if it does) when I install it.

Interesting....Z1 states (in my question via their website and Instagram) that, although specifically designed for the Z1 diff cover, the same brace does fit OEM and Nismo diff covers. So I am surprised there is actually a slightly different version of this brace specifically designed for the OEM cover.

Rusty · 02-05-2019, 09:50 PM

Quote:

Originally Posted by cv129

Interesting....Z1 states (in my question via their website and Instagram) that, although specifically designed for the Z1 diff cover, the same brace does fit OEM, Nismo diff covers. So I am surprised there is actually a slightly different version of this brace specifically designed for the OEM cover.

That's what I read too. That it will fit both stock and Z! covers.

01-31-2019, 01:20 PM	#47 (permalink)
JTM88 Enthusiast Member Join Date: Oct 2016 Location: Houston, TX Posts: 276 Drives: 2012 370Z Rep Power: 14	I'm glad I waited, that's pretty crappy of Z1 to remove reviews. __________________ 2012 Base Gun Metallic MT6 -CNT Racing CBE-Swift Sport Springs-Sport Akebono BBK-Z1 Motorsports Intakes-König Oversteer Wheels-1320 Resonated Test Pipes -RJM Rev 2.1 Clutch Pedal-

01-31-2019, 04:42 PM	#49 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,217 Drives: 2011 Nismo GM 6M Rep Power: 2684438	This is the review that I'm posting again. If you have exhaust like FI that are close to the diff. This brace won't fit unless you trim about 1 3/8" on the corner of the brace. The other problem is that the upper mounting hole does not line up with the hole in the sub-frame. It's off by a bolt hole diameter. They say to loosen the diff bolting up to the diff so that you can move the diff around and get the holes to line up. Problem is if you have a solid bushing like SPL. When tightening the diff bolting back down. This will put stress on the bolting that you don't need. If you have the stock rubber bushing. you might get away with it. The other thing that I noticed. There is weld beads on both sides of the bends of the brace. It looks like when bending the metal to shape. The metal cracked at the bends. So they welded over the cracks to hide them. Rusty gbrettin and redondoaveb like this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

01-31-2019, 04:45 PM	#50 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,217 Drives: 2011 Nismo GM 6M Rep Power: 2684438	Just seen this on the Z1 website. "Thank you for your review. It has been submitted to the store owner for approval and should appear shortly." gbrettin, Hotrodz, jchammond and 1 others like this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

01-31-2019, 07:21 PM	#51 (permalink)
Spoiler A True Z Fanatic Join Date: Jun 2015 Location: Central Florida Age: 65 Posts: 8,409 Drives: 21 Supra -Blk/Red Rep Power: 2684380	All you can do is be honest... and sounds like you were... gbrettin, Rusty, Hotrodz and 1 others like this. __________________ … I SUPPORT HOES WITH SUPPORT HOSE…

02-01-2019, 09:32 AM	#52 (permalink)
2011 Nismo#91 A True Z Fanatic Join Date: Mar 2011 Location: NJ Posts: 2,401 Drives: slowly Rep Power: 40569	You won't find a single bad review at Z1 or Stillen or any small vendor, their products are always excellent every time. Except when there not and those don't get approved. JARblue, DarkJak, Chuck33079 and 5 others like this. __________________ GTR TT 493Whp/431lbft, Ecutek, Southbend 6puck,Quaife, RPM RollBar 4Point, R888R, JRZ RSPro F(10R/10C) R(10R/6C) 1000f500r inlbs+150inlbs Tender, SPL everywhere.Full Specs

02-03-2019, 06:15 AM	#53 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 43 Posts: 36,450 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	Z1 routinely deletes negative reviews from what I can tell. I've had a couple deleted and know several others that have experienced the same thing. Rusty, Memphis370Z and Zthirty4NISMO like this. __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

02-03-2019, 11:05 AM	#54 (permalink)
Bswanny Base Member Join Date: Mar 2018 Location: New Mexico Posts: 135 Drives: 20 370Z Sport Rep Power: 7	Personally I have only had poor quality parts from Z1 and am told to shut up because everyone thinks Z1 is god. I feel bad for you the brace didn't work but when I read it's a direct fit for the 350Z and you need to unbolt the diff for the 370Z, I knew corners were cut. They used the same piece for two different applications to save costs. Shame Sent from my SAMSUNG-SM-G930A using Tapatalk Rusty and Brendan like this.

02-05-2019, 08:24 PM	#58 (permalink)
bpchaos Base Member Join Date: Oct 2016 Location: Los Angeles, CA Posts: 74 Drives: G37S (370z+ seats) Rep Power: 3364	Bell Raceworks makes a slightly different brace for those with stock diff covers. I'll let you all know how that one fits (if it does) when I install it.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
2015+ Nismo Rear Chassis Brace Install	nismolucino	DIY Section (Do-It-Yourself)	9	02-22-2021 12:00 PM
Z1 Brake Master Cylinder Brace - Install Help	140BPM	Brakes & Suspension	10	04-22-2019 10:06 PM
Has anyone been able to install a Z1 master cylinder brace?	gshort24	Brakes & Suspension	4	08-11-2016 03:05 PM
Rear brace bar removal/install?	TriNismo	Exterior & Interior	8	08-18-2015 12:02 AM