Goodridge SS Brake line Upgrade: Flush/Bleeding Issues

JSBZ · 12-20-2009, 11:13 AM

Yesterday, I installed a set of Goodridge SS lines, Ferodo 2500 pads and Motul 600 fluid. I cannot get the pedal to firm up. I purged the system before cracking open the lines and then bled the system twice using a Motive power bleeder (15psi) after install. I am not getting any air bubbles showing in the fluid.
I didn't disable the ABS (manual says to disable) until the second bleed but it didnt seem to matter.
Any ideas?
BTW, ss kit was quality, easy to install and fit perfect.

SOLISIMO · 12-20-2009, 11:15 AM

Other than the obvious problem, are you satisfied with the quality and build? Im looking for a set...

ChrisSlicks · 12-20-2009, 11:33 AM

The pedal goes completely to the floor? I had this problem once in another car when I made the mistake of letting all the fluid drain out of the system when replacing the calipers, always plug the lines temporarily when you are swapping out the hoses!

You are now going to need an ABS Diagnostic tool to put the ABS system into purge mode. Unfortunately these are non-standard for foreign cars so it's going to have to get towed to the dealer unless you can find somebody with one.

JSBZ · 12-20-2009, 01:28 PM

I feel dumb! Didn't catch the back side bleeders. Bled again and now the pedal is hard as a rock.
Initial impression: lost some braking modulation but the bite is intense. More to follow.

cavemancan · 10-23-2012, 05:21 PM

Quote:

Originally Posted by JSBZ

Didn't catch the back side bleeders.

Back side bleeders??? Can someone please explain? Is there another location on the same caliper that needs to be bled?

I'm having the same issue...No ABS light...no leaks...no more bubbles. Pedle is almost ok feeling...approx. 20% mushier than stock when it should feel firm as hell. ABS was unplugged during bleed.

sig11 · 10-24-2012, 10:45 AM

Quote:

Originally Posted by cavemancan

Back side bleeders??? Can someone please explain? Is there another location on the same caliper that needs to be bled?

I'm having the same issue...No ABS light...no leaks...no more bubbles. Pedle is almost ok feeling...approx. 20% mushier than stock when it should feel firm as hell. ABS was unplugged during bleed.

There are bleeders on both sides of the sport calipers... have to do both.

JSBZ · 12-20-2009, 01:35 PM

Quote:

Originally Posted by SOLISIMO

Other than the obvious problem, are you satisfied with the quality and build? Im looking for a set...

Quality is top notch. Fit is perfect. I ended up using the factory lock plates instead of the (4) supplied. The supplied plates were a PITA to install, didn't quite fit.
FYI, I am running Akebono's.

SilverBullet · 12-20-2009, 01:30 PM

What do you mean by braking modulation?

JSBZ · 12-20-2009, 01:52 PM

Quote:

Originally Posted by SilverBullet

What do you mean by braking modulation?

It takes less pedal to get the same amount of braking. The brakes felt grabby until I adjusted my braking style. My only frame of reference for now is the street. I am sure it will be different on the track with higher speeds.

SilverBullet · 12-20-2009, 01:36 PM

Did you bed the pads in yet?

JSBZ · 12-20-2009, 01:53 PM

Quote:

Originally Posted by SilverBullet

Did you bed the pads in yet?

Yes, per Ferodo instructions.

radio5boro · 12-20-2009, 01:57 PM

Yeah this happened to me when installing my stoptech ss lines on my g35c. I didn't bleed the brembos as good as I thought and i forgot about the backside. The pedal hit floor without braking at all. I then rebled and the brakes were perfect again.

SOLISIMO · 12-20-2009, 01:36 PM

Thanks dude.....

SilverBullet · 12-20-2009, 01:58 PM

Thanks for the information JSBZ.

NewYorkJon34 · 06-15-2010, 03:39 PM

I just installed the Z1 brake lines, and had the guy rebleed the brake lines twice, I'm really starting to think that I should return the Z1 lines & get the goodridge lines. My petal was almost hitting the floor & now I have to double tap the brakes everytime to get the pressure up. It's just really inconsistant & idk what to do.

12-20-2009, 11:13 AM	#1 (permalink)
JSBZ Base Member Join Date: Jun 2009 Location: Colorado Posts: 56 Drives: 09 370Z T/S 6MT Rep Power: 16	Goodridge SS Brake line Upgrade: Flush/Bleeding Issues Yesterday, I installed a set of Goodridge SS lines, Ferodo 2500 pads and Motul 600 fluid. I cannot get the pedal to firm up. I purged the system before cracking open the lines and then bled the system twice using a Motive power bleeder (15psi) after install. I am not getting any air bubbles showing in the fluid. I didn't disable the ABS (manual says to disable) until the second bleed but it didnt seem to matter. Any ideas? BTW, ss kit was quality, easy to install and fit perfect.

12-20-2009, 11:15 AM	#2 (permalink)
SOLISIMO Track Member Join Date: Apr 2009 Location: Florida Posts: 510 Drives: TOP SECRET G37S Rep Power: 17	Other than the obvious problem, are you satisfied with the quality and build? Im looking for a set... __________________ AUTOKITS-X CF GRILLE l INJEN CAI l STILLEN SWAYS l MXP EXHAUST l LE CF MIRRORS l SSR'S l HANKOOK'S l TS COILOVERS l TS BUMPER l TS DIFFUSER l TS SIDE SKIRTS l SEIBON CF TS HOOD l TS AEROCATCH l 3K HID FOGS l KICS R40'S l ILLUMINATED SILLS l GROUNDING KIT l VLEDS l

12-20-2009, 01:36 PM	#13 (permalink)
SOLISIMO Track Member Join Date: Apr 2009 Location: Florida Posts: 510 Drives: TOP SECRET G37S Rep Power: 17	Thanks dude..... __________________ AUTOKITS-X CF GRILLE l INJEN CAI l STILLEN SWAYS l MXP EXHAUST l LE CF MIRRORS l SSR'S l HANKOOK'S l TS COILOVERS l TS BUMPER l TS DIFFUSER l TS SIDE SKIRTS l SEIBON CF TS HOOD l TS AEROCATCH l 3K HID FOGS l KICS R40'S l ILLUMINATED SILLS l GROUNDING KIT l VLEDS l

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Upgrade Your brake Fluid! Endless, Motul, Ate!	corner3garage	Suspension/Brakes	439	02-18-2015 11:46 AM
Do you want Goodridge braided steel brake lines for the 370Z?	semtex	Brakes & Suspension	34	01-13-2010 11:25 AM
Hella Flush III	Nick911sc	The Lounge (Off Topic)	13	12-02-2009 07:37 PM
thinking of buying 370z, then GTM turbo's , but overheat issues,oil issues ??	Christopher	Nissan 370Z General Discussions	19	10-16-2009 03:55 PM
Initial Z issues that are now non-issues......	cave vulture	Nissan 370Z General Discussions	1	09-06-2009 10:19 PM

12-20-2009, 11:33 AM	#3 (permalink)
ChrisSlicks A True Z Fanatic Join Date: Mar 2009 Location: North East Posts: 6,203 Drives: 09 370Z Sport M6 Rep Power: 654	The pedal goes completely to the floor? I had this problem once in another car when I made the mistake of letting all the fluid drain out of the system when replacing the calipers, always plug the lines temporarily when you are swapping out the hoses! You are now going to need an ABS Diagnostic tool to put the ABS system into purge mode. Unfortunately these are non-standard for foreign cars so it's going to have to get towed to the dealer unless you can find somebody with one.

12-20-2009, 01:28 PM	#4 (permalink)
JSBZ Base Member Join Date: Jun 2009 Location: Colorado Posts: 56 Drives: 09 370Z T/S 6MT Rep Power: 16	I feel dumb! Didn't catch the back side bleeders. Bled again and now the pedal is hard as a rock. Initial impression: lost some braking modulation but the bite is intense. More to follow.

12-20-2009, 01:30 PM	#8 (permalink)
SilverBullet Track Member Join Date: Dec 2009 Location: California Posts: 873 Drives: 2008 G37 Rep Power: 17	What do you mean by braking modulation?

12-20-2009, 01:36 PM	#10 (permalink)
SilverBullet Track Member Join Date: Dec 2009 Location: California Posts: 873 Drives: 2008 G37 Rep Power: 17	Did you bed the pads in yet?

12-20-2009, 01:57 PM	#12 (permalink)
radio5boro Base Member Join Date: Sep 2009 Location: Queens, NY Posts: 158 Drives: 09 MBlue 370z 6MT Rep Power: 16	Yeah this happened to me when installing my stoptech ss lines on my g35c. I didn't bleed the brembos as good as I thought and i forgot about the backside. The pedal hit floor without braking at all. I then rebled and the brakes were perfect again.

12-20-2009, 01:58 PM	#14 (permalink)
SilverBullet Track Member Join Date: Dec 2009 Location: California Posts: 873 Drives: 2008 G37 Rep Power: 17	Thanks for the information JSBZ.

06-15-2010, 03:39 PM	#15 (permalink)
NewYorkJon34 A True Z Fanatic Join Date: Jun 2009 Location: Naples, Florida Posts: 3,041 Drives: 09 Fairlady Z Rep Power: 1065	I just installed the Z1 brake lines, and had the guy rebleed the brake lines twice, I'm really starting to think that I should return the Z1 lines & get the goodridge lines. My petal was almost hitting the floor & now I have to double tap the brakes everytime to get the pressure up. It's just really inconsistant & idk what to do.