Z1 Master cylinder brace installed.

eastwest2300

So I installed mine a couple months ago, and just recently, I installed Mr. Rusty's brace ^^ too.. I got 2 of the 3 bolts in.. and it was a lot easier to install the 2nd time around..

Let me give you guys a trick that really worked for me.. I took 2 zip ties and with one I made a circle.. the 2nd zip tie, I zip tied (not anywhere tight, I could easily fit 3 fingers) the bar that separates the master cylinder area from the engine bay, now take that 1st zip tie and interloop it to the 2nd. (like 2 wedding bands interlooped)

if you did this right, you should have 1 zip tie to the small metal bar, and another zip tie interlooped and hanging freely...now you'll take that zip tie thats hanging and use that with the gold nut (its actual threads) from the master cylinder to place down in the mounting location, and those zip ties will hold that nut into place while you can focus on lining up your holes..

I then used a socket with a allen head with really good lighting to get the upper and lower bolts into the holes.

__________________
Infiniti QX70 & Toyota Supra 3.0 Premium

eastwest2300

Needless to say, the first time I installed it, it took me a good bit of time.. and lots of frustration, the 2nd time I did it.. I knocked it out in 30 to 40 minutes (easily).. i spent more time getting them 3 caps out then installing the actual brace.

__________________
Infiniti QX70 & Toyota Supra 3.0 Premium

Infiniti370z

The reason why some of us apparently can only get two out of the three bolts install at the same time is because the holes in the bracket were not machined out correctly and do not line up, at least it didn't on my 14 Nismo. After fighting it for a while(enough time to get pissed off lol) I noticed the misalignment. I took it back out and bored out the center hole down to line it up with the threads, finally got all three in. I'm pretty sure it would have been fine with two bolts but I wasn't trying to be defeated by a stupid simple bracket aka OCD. I emailed z1 about it, Shanna replied asking me if someone from parts team has contacted me, I replied no and haven't heard anything since. My apologies for the orientations of the pictures.

Attached Images

	20171202_011348.jpg (597.4 KB, 87 views)
	20171202_015904.jpg (680.8 KB, 71 views)
	20171202_020833.jpg (658.1 KB, 70 views)

__________________
//RAYS ENGINEERING//Z1 MOTORSPORTS//NISMO//RADI-CAL BBK//SPARCO//3M//ESCORT//BLENDMOUNT//BOSE//AAM//GTR//THE RETROFIT SOURCE//MILLENNIA
2014 Nismo BLK//2004 Sentra SE-R Spec-v//2013 Prius 4//Sold 2010 370z GM base 6MT

Rusty

eastwest installed mine. We got all 3 bolts in with little problem.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

Infiniti370z

I wonder if it's hit or miss with the machining?

__________________
//RAYS ENGINEERING//Z1 MOTORSPORTS//NISMO//RADI-CAL BBK//SPARCO//3M//ESCORT//BLENDMOUNT//BOSE//AAM//GTR//THE RETROFIT SOURCE//MILLENNIA
2014 Nismo BLK//2004 Sentra SE-R Spec-v//2013 Prius 4//Sold 2010 370z GM base 6MT

Rusty

Could be the car it's self. The brace is cnc machined. So they all should be the same. But if they are using 2 different cnc's or a bit breaks when machining and they don't recalibrate after changing it. That could be an issue.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

Infiniti370z

My money is on the machining lol

Sent from my SM-N950U using Tapatalk

__________________
//RAYS ENGINEERING//Z1 MOTORSPORTS//NISMO//RADI-CAL BBK//SPARCO//3M//ESCORT//BLENDMOUNT//BOSE//AAM//GTR//THE RETROFIT SOURCE//MILLENNIA
2014 Nismo BLK//2004 Sentra SE-R Spec-v//2013 Prius 4//Sold 2010 370z GM base 6MT

madwi

I believe EW was only able to get two out of the three on his car too.

redondoaveb

I installed my brace today, could only get the two outer bolts installed. I still don't have the jam nut real tight up against the brace, I didn't have the right 19mm. What a pain in the ***. I'm glad I had a telescopic magnet to retrieve the bolts I dropped multiple times.

__________________
Fast Intentions "Stage Seb" twin turbo #098- Specialty Z/Tial-Xonarotor/CJM/Ecutek/HKS/KW/SPL/Hotchkis/Rohana/Toyo
700+whp

soill370z

DUDE! Exactly the same as me hahaha

Ventruck

Haven't looked at my brace in a while, but noticed the middle hole is shown as a slot now. 99% sure it wasn't like that before.

My OCD wants to get this so I have 3 bolts in, but just placed an order for other stuff at Z1, so maybe the next go around.

https://www.z1motorsports.com/brakes...ce-p-9538.html

tims370z

This was such a good tip with the zip ties. Thank you! Still having trouble with getting the bolts in due to not having the right tools. I got the top one in. I’m going to assume that the easiest. Has anyone tried these bendable extensions? I’m going to give them a whirl. My hands hurt after an hour and half of torture.

ABN Flexible Socket Extension Cable Flex Bar Ratchet Light Impact Tools 4-Piece Set of 1/4” Inch Drive & 3/8” Inch Drive https://www.amazon.com/dp/B074ZNS1ZC..._kh5zCbET2HJX0



Sent from my iPhone using Tapatalk

wanker

Those might work. What I used was a universal joint attached to a socket extender. I used painters tape to attach the bolt to the allen bit.

tims370z

I’ll report back here if they do

tims370z

Universal joint and the flexible extenders were the ticket. Got all three bolts in!