Rear specs

FLUJOKE · 09-28-2015, 01:34 PM

Not sure if this is good specs or not? I'm daily street driven a track MAYBE once a year. 370 sport stock tire size.

Sent from my iPhone using Tapatalk

FLUJOKE · 09-28-2015, 01:34 PM

Sent from my iPhone using Tapatalk

FLUJOKE · 09-28-2015, 01:37 PM

Oh yeah, alignment is for swift springs.

Sent from my iPhone using Tapatalk

gomer_110 · 09-28-2015, 02:44 PM

You need less camber if you don't want to eat tires in the rear. Personally I'd run closer to -1.5 to -1.7. Not sure about the toe as it's in degrees but fwiw I have my rear toe set to 1/16" toe in total.

NORAIN · 09-28-2015, 05:34 PM

Quote:

Originally Posted by gomer_110

You need less camber if you don't want to eat tires in the rear. Personally I'd run closer to -1.5 to -1.7. Not sure about the toe as it's in degrees but fwiw I have my rear toe set to 1/16" toe in total.

That's a lot of toe in too, 1/4"+.
.03123 = 1/32" ea side, or .0625 = 1/16" total toe.
Toe in or out is actually more of a tire eater than the camber. I ran -2.5 rear camber until I got toe bolts without much uneven wear at all. That was with the same rear toe setting rear, 1/16", in and dead Zero in front.

FLUJOKE · 09-28-2015, 05:38 PM

I'm so lost. So what should I be at guys? I see degrees of total .30 total toe. What should it be at then?

Sent from my iPhone using Tapatalk

NORAIN · 09-28-2015, 06:13 PM

You're just under 3/8" toed in = .30 That's a lot.
Think of .5 = 1/2", .25 = 1/4", .125 = 1/8", etc.

Silly Rabbit · 09-28-2015, 06:30 PM

Did the lock out bolts work for you?

FLUJOKE · 09-28-2015, 08:07 PM

Yes I got the lockout bolts on. So what fraction/ degree should I be at kind people.

Sent from my iPhone using Tapatalk

gomer_110 · 09-28-2015, 08:40 PM

Just go with 0 toe. Honestly the difference between 0 toe and whatever 1/16" total toe in is in degrees is probably insignificant for most people handling wise (I sure I probably couldn't tell the difference).

jchammond · 09-28-2015, 08:46 PM

Quote:

Originally Posted by gomer_110

Just go with 0 toe. Honestly the difference between 0 toe and whatever 1/16" total toe in is in degrees is probably insignificant for most people handling wise (I sure I probably couldn't tell the difference).

if you go 0 toe; you may lose control on high speed acelleration! Toe number's look fine.
also if you don't burn your tires/camber will be ok-better cornering.
i got -1.7 camber & still smoke the inner part of my tires more.
as far as toe.....a guy set mine at 0 & ~Z~ was very unstable under hard acceleration above 80...lots of dancing around in back.
Road force will pull tires outwards somewhat.

FLUJOKE · 09-28-2015, 08:47 PM

So main objective I'm getting from all this is to take rear camber to -1.5 to -1.7..... What is the degree in toe to get, b/c i don't want 0 toe if I'm going to lose control. thank you all for the help

jchammond · 09-28-2015, 08:50 PM

Quote:

Originally Posted by FLUJOKE

Sent from my iPhone using Tapatalk

Also; as you adjust camber more + (outwards) toe will increase (inward) and will need to be adjusted back to spec.
Alway's be sure and do rear alignment first before going to the front!
have a good evening.

jchammond · 09-28-2015, 08:52 PM

Quote:

Originally Posted by FLUJOKE

So main objective I'm getting from all this is to take rear camber to -1.5 to -1.7..... What is the degree in toe to get, b/c i don't want 0 toe if I'm going to lose control. thank you all for the help

You dead on in spec right now!

jchammond · 09-28-2015, 08:54 PM

A little old lady could get by with 0 rear toe; but i'm subject to hit the speed limiter..oops

09-28-2015, 01:34 PM	#1 (permalink)
FLUJOKE Track Member Join Date: Apr 2012 Location: earth Posts: 770 Drives: car Rep Power: 2067	Rear specs Not sure if this is good specs or not? I'm daily street driven a track MAYBE once a year. 370 sport stock tire size. Sent from my iPhone using Tapatalk

09-28-2015, 02:44 PM	#4 (permalink)
gomer_110 A True Z Fanatic Join Date: Aug 2011 Location: Perrysburg, OH Posts: 17,992 Drives: '11 Nismo #528 GM Rep Power: 36941	You need less camber if you don't want to eat tires in the rear. Personally I'd run closer to -1.5 to -1.7. Not sure about the toe as it's in degrees but fwiw I have my rear toe set to 1/16" toe in total. Rusty likes this. __________________ '11 370Z Nismo #528 Fast Intentions \| Stillen \| Motordyne \| Uprev \| CSF \| Zspeed \| Z1 Motorsports \| AST \| Swift \| SPC \| SPL \| Whiteline \| Hotchkis \| Bride \| Schroth \| Robispec \| Cusco \| Nismo \| Volk \| Forgestar \| Hoosier \| RJM '17 Titan Bone Stock

09-28-2015, 06:13 PM	#7 (permalink)
NORAIN Enthusiast Member Join Date: Jun 2013 Location: Wilmington, NC Age: 57 Posts: 323 Drives: 2011 370Z 6M SP Rep Power: 12	You're just under 3/8" toed in = .30 That's a lot. Think of .5 = 1/2", .25 = 1/4", .125 = 1/8", etc. __________________ Swift Springs\|265-305 RE-11\|Forgestar F14\|F.I. TDX S.S. 12" Res."Milled Out"\|K&N\|SPL\|Z1(34 row)oil cooler\|Z1 brake upgrade\|Hotchkis Zspeed\|Team Voodoo\|HPDEjunkie.com

09-28-2015, 06:30 PM	#8 (permalink)
Silly Rabbit Track Member Join Date: Sep 2013 Location: Brookston, IN Age: 54 Posts: 683 Drives: '12 PW Touring Sport Rep Power: 619	Did the lock out bolts work for you? __________________ NISMO R Tune Intakes \ Fast Intentions RHFC \ Borla CBE \ EcuTek Tuned\ SPL Camber Arms \ Powertrix Coilovers \ Swift Springs \ Avant Garde \ Wicked CAS \ Morimoto XB Halos \ Custom Fenders \ Hotchkis Sways \ NLP Splitter

09-28-2015, 08:40 PM	#10 (permalink)
gomer_110 A True Z Fanatic Join Date: Aug 2011 Location: Perrysburg, OH Posts: 17,992 Drives: '11 Nismo #528 GM Rep Power: 36941	Just go with 0 toe. Honestly the difference between 0 toe and whatever 1/16" total toe in is in degrees is probably insignificant for most people handling wise (I sure I probably couldn't tell the difference). __________________ '11 370Z Nismo #528 Fast Intentions \| Stillen \| Motordyne \| Uprev \| CSF \| Zspeed \| Z1 Motorsports \| AST \| Swift \| SPC \| SPL \| Whiteline \| Hotchkis \| Bride \| Schroth \| Robispec \| Cusco \| Nismo \| Volk \| Forgestar \| Hoosier \| RJM '17 Titan Bone Stock

09-28-2015, 01:34 PM	#2 (permalink)
FLUJOKE Track Member Join Date: Apr 2012 Location: earth Posts: 770 Drives: car Rep Power: 2067	Sent from my iPhone using Tapatalk

09-28-2015, 01:37 PM	#3 (permalink)
FLUJOKE Track Member Join Date: Apr 2012 Location: earth Posts: 770 Drives: car Rep Power: 2067	Oh yeah, alignment is for swift springs. Sent from my iPhone using Tapatalk

09-28-2015, 05:38 PM	#6 (permalink)
FLUJOKE Track Member Join Date: Apr 2012 Location: earth Posts: 770 Drives: car Rep Power: 2067	I'm so lost. So what should I be at guys? I see degrees of total .30 total toe. What should it be at then? Sent from my iPhone using Tapatalk

09-28-2015, 08:07 PM	#9 (permalink)
FLUJOKE Track Member Join Date: Apr 2012 Location: earth Posts: 770 Drives: car Rep Power: 2067	Yes I got the lockout bolts on. So what fraction/ degree should I be at kind people. Sent from my iPhone using Tapatalk

09-28-2015, 08:47 PM	#12 (permalink)
FLUJOKE Track Member Join Date: Apr 2012 Location: earth Posts: 770 Drives: car Rep Power: 2067	So main objective I'm getting from all this is to take rear camber to -1.5 to -1.7..... What is the degree in toe to get, b/c i don't want 0 toe if I'm going to lose control. thank you all for the help Last edited by FLUJOKE; 09-28-2015 at 08:51 PM.

09-28-2015, 08:54 PM	#15 (permalink)
jchammond A True Z Fanatic Join Date: Nov 2014 Location: South Carolina Age: 58 Posts: 15,204 Drives: 13’ 370Z TS 7A/T Rep Power: 2684394	A little old lady could get by with 0 rear toe; but i'm subject to hit the speed limiter..oops __________________ MazWorx built long block \| FI-TT-100 Stage 2.75 \| IPT built 7A/T http://www.the370z.com/members-370z-...s-musings.html

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Anyone have these specs?	BadChachi	Wheels & Tires	28	05-21-2015 06:50 PM
SPL Camber arms & New alignment specs Rear is super loose	Rangerz	Brakes & Suspension	7	03-04-2014 02:52 AM
What might be the specs to this car	Good_Tymes	Exterior & Interior	6	04-04-2013 08:15 PM
Specs of the 3.7L VQ37VHR	admin	Engine & Drivetrain	17	11-12-2012 05:18 PM