Power wire gauge through firewall?

bigaudiofanat · 07-29-2014, 08:14 PM

Quote:

Originally Posted by RonRizz

A little lube works wonders

That's the joke when I do a install. big always brings the lube.

IDEAL INDUSTRIES, INC. - ClearGlide™ Wire Pulling Lubricant

RonRizz · 07-30-2014, 04:23 PM

madwi · 08-02-2014, 08:48 PM

Quote:

Originally Posted by Nillaz

I spec'd it with a 4ga kit but can anyone tell me definitively if this will fit through the grommet in the firewall behind the battery? It's been two years since I last had to do this and can't for the life of me remember what I ran last time. I just perused the install videos as a refresher and I'm sure it's listed in there somewhere but I must have missed it. I suspect I should be OK but confirmation would give me some peace of mind. If it's not going to fit I'll order another amp kit immediately.

Thanks!

I think you might of watched this vid:
Video#5 Audio Install In a 2009 370Z on Vimeo
Around 2:00 minute mark he shows the routing of 4 gauge wire to a unused grommet on the drivers side of the car.

Minhtin · 08-02-2014, 10:27 PM

I think that spot is only accessible if you have the automatic version. If you have a manual, it's almost impossible to reach it.

Nillaz · 08-02-2014, 11:23 PM

Quote:

Originally Posted by Minhtin

I think that spot is only accessible if you have the automatic version. If you have a manual, it's almost impossible to reach it.

Yeah, you definitely can't use the drivers side location if you have manual. I would have preferred something a little neater than using that rubber boot on the passenger side, but ultimately it got the job done just fine. I didn't end up using any lube for the wire like most others, just pulled it through with a glow rod.

Minhtin · 08-03-2014, 03:04 AM

Working on car and raving at the same time! Awesome.

Nillaz · 08-03-2014, 03:30 AM

Quote:

Originally Posted by Minhtin

Working on car and raving at the same time! Awesome.

is just how I do!

madeinjapan · 07-13-2016, 08:36 AM

Quote:

Originally Posted by bigaudiofanat

This should help

saved me a ton of time i had no idea how i was getting through

07-30-2014, 04:23 PM	#17 (permalink)
RonRizz A True Z Fanatic Join Date: Aug 2011 Location: Pine grove, Pa Posts: 2,136 Drives: 2 feet, 3 pedals Rep Power: 6775	__________________ P99rs Head Unit--- Amps- 2 Pioneer Prs800d --- Zapco ST1000MX---Zapco ST-4XSQ---- SI BM mk5 Subs---SI TM65v2 Midbass--- SI M3 mids--- SI M25 xbl2 tweeters ----- 2016 MECA street class 3rd place at world finals

08-02-2014, 10:27 PM	#19 (permalink)
Minhtin Base Member Join Date: Jun 2014 Location: Ca Posts: 99 Drives: 14 370z Nismo PW Rep Power: 11	I think that spot is only accessible if you have the automatic version. If you have a manual, it's almost impossible to reach it. madwi likes this.

08-03-2014, 03:04 AM	#21 (permalink)
Minhtin Base Member Join Date: Jun 2014 Location: Ca Posts: 99 Drives: 14 370z Nismo PW Rep Power: 11	Working on car and raving at the same time! Awesome. Nillaz likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Question on power wire run and engine bay	ksagis	Audio & Video	5	12-27-2013 10:05 AM
DEFI Red Racer Oil Pressure Gauge Wire Extension?	Cell	Exterior & Interior	0	09-05-2013 01:04 AM
power wire run?	x102x	Audio & Video	8	07-05-2011 12:21 PM
power wire size for JL audio 900/5	Danny3.7	Audio & Video	3	07-19-2010 09:50 PM
RCA cables and power wire	BobQ	Audio & Video	16	02-27-2010 09:07 AM