Problems and Fixes After Car Audio Installs

rreign

I have seen a lot of guys come in here and start a new thread because they had some kind of issue after a car audio install. Rather than everyone coming in here, NOT searching, then starting a new thread... I'm starting a comiliation in hopes that the multiple duplicate threads will stop! I have pulled this info from other threads that responded to such problems. I will add more as more problems occur. Feel free to send me new solutions to add to this thread. Or just post your own solutions. Thanks everyone.


WINDOWS NOT WORKING PROPERLY AFTER INSTALL
If the windows do not close automatically
If the power window automatic function (closing
only) does not operate properly, perform the
following procedure to initialize the power
window system.

1. Push the ignition switch to the ON position.

2. Close the door.

3. Open the window completely by operating
the power window switch.

4. Pull the power window switch and hold it to
close the window, and then hold the switch
more than 3 seconds after the window is
closed completely.

5. Release the power window switch. Operate
the window by the automatic function to
confirm the initialization is complete.

6. Perform steps 2 through 5 above for other
windows.


AIRBAG LIGHT COMING ON AFTER CAR AUDIO INSTALL

****IIMPORTANT****
Turn the ignition off as soon as the airbag light goes out the first time.


If you have the airbag light blinking here is how to reset it:

1. Push the start button two times (Ignition on but engine not started).

2. Watch the airbag light closely. It will stay on for a few secs. and then as soon as it blinks off (the start of the flashing), turn the key off INSTANTLY.

3. Count to 5 (1 Mississippi, 2 Mississippi . . . .)

4. Repeat steps 1-3 two more times until you have done the cycle three times.

5. Now turn the key on and watch the light. It will start blinking in a different, slower manner. This is diagnostic mode. You can watch this for a little while, no hurry.

6. Now turn the key off again, Count to 5 like in step 3 again, and turn back on. If the procedure worked, the airbag light will not be flashing.

If it does not work the first time, just repeat the steps again.


PROBLEMS WITH STEERING WHEEL HARNESS
(This is specifically for the SWI-JACK Harness)

1. Quick description before we start wiring the SWI-JACK .
The SWI-JACK 's wire color we are going to use is White. This is the White wire on the SWI-JACK , not the vehicle!
The other wires on the SWI-JACK , green, yellow, orange and blue wires are not used for your Nissan 370Z.

This leaves you with a Red, Black and two loop wires. These wires will be discussed down below.

2. Picture of the Nissan 370Z plug.
Connector picture is unavailable. Either we don't have a picture to show or we have to get the wire somewhere else and not at the factory radio harness.

3. Connecting the SWI-JACK 's steering wheel control input wire to vehicle plug.
Connect the SWI-JACK 's White wire to PIN 16 (Blue) with a 150 ohm resistor, PIN 15 (Pink) with a 47 ohm resistor
Connect free ends of resistors to interface's White wire.
Ground the BROWN wire found in the same radio connector.



4. Connecting power and ground wires.
Black wire: Connect the SWI-JACK 's black wire to chassis ground. This is usually a black wire on the aftermarket wire kit.
Red wire: Connect the SWI-JACK 's red wire to a switched +12volt wire. This is usually a red wire on the aftermarket wire kit.

5. Instructions for cutting or not cutting loop wires.
Step A: The purple loop wire does not need to be cut.
Step B: Cut the Brown loop wire in half and insulate both ends.

6. Programming the SWI-JACK with a version number.
The SWI-JACK has to be programmed for version # 3.
1. Press and hold the Program Button on the SWI-JACK while turning on the vehicle to the accessory position. The LED will turn on.
2. Release the Program Button and the LED will turn off.
3. Press the Program Button 3 times. Each time you press and release the Program Button, the LED will turn on and off. Once you press the Program Button 3 times, wait for 3 seconds. The LED will flash 3 times indicating it is programmed for version 3. If it flashes the wrong version number, you will have to start all over at step 1 above in this section. Turn the key off.
4. Once you have programmed the correct version number, you will not have to do these steps again. If you need to reprogram the steering wheel control, you can go directly to the next section.

7. Programming the SWI-JACK to learn steering wheel control functions.
1. Turn the key to the accessory position (you do not need to hold the Program Button at this time). The LED will flash 3 times. This indicates it is programmed for version 3.
2.
Press the Program Button until the LED turns on, then release the button (This will erase all previous learned steering wheel control functions). The SWI-JACK is now ready to learn a command from the steering wheel.

3.
The SWI-JACK must be programmed in the specific order shown in the chart below. If a function is not needed, it may be skipped. Adjust the Radio Select switch on the side of the SWI-JACK according to the chart. Alpine = 1, JVC = 2, Kenwood = 3, Clarion = 4 and Blaupunkt = 5.


Alpine
JVC
Kenwood
Clarion
Blaupunkt
Switch setting for
SWI-JACK
1
2
3
4
5
1
Volume Up Volume Up Volume Up Volume Up Volume Up
2
Volume Down Volume Down Volume Down Volume Down Volume Down
3
Mute Mute/Power Mute Mute Mute
4
Preset Up Preset Up Source
Track Up

Source
5
Preset Down Source Seek Up Track Down Track up
6
Source Seek Up Track Up Band Track down
7
Track Up Seek Down Track Down Source Disc up
8
Track Down Select Disc Up/FM Disc down
9
Power Band Disc Down/AM OK
10
Ent/Play
11
Band/Program
4. With the LED on, press your steering wheel button until the light goes out and hold for one second more.
5. Release and the LED should come back on. If it does not please double check all connections and verify for correct version programming.
6. Repeat step 4 and 5 to program additional steering wheel buttons in the order corresponding to the chart above for your SWI interface.
7. If you come across a command in the chart that your steering wheel does not have, or you do not want to program, press the Program Button on the side of the SWI interface.
8. The LED will flash once rapidly and then stay on confirming that you have successfully skipped that command and are ready for the next button.
9. When you are done programming all the buttons, wait for about 7 seconds. The LED will flash 3 times indicating it is done programming. The LED will then flash 3 times indicating the version number.


8. Testing the SWI-JACK .
1. Connect the plug to back of radio's steering wheel input jack or harness.
2. With the vehicle on, press a steering wheel button to control the stereo. The SWI-JACK should control the aftermarket stereo with the function you taught it. Test all other buttons.
3. If the interface does not control the radio as the steering wheel indicates, the buttons were either pressed in the wrong order or a step was not skipped properly. Return to category 7 and reprogram.
4. Make sure all unused wires are isolated separately.
5. After all commands are verified to work properly, secure the SWI interface so that tension will not pull either of the connectors loose or apart.
6. That's it! Enjoy!

__________________
Become a Premium Member...CLICK MEOW