Caution with 2013 models and install

bigaudiofanat · 08-01-2013, 03:10 PM

Quote:

Originally Posted by Baer383

I used a Metra harness and had no issues on my 2013 Nismo.

As stated earlier it could be early 2013 models used the older style. However in this instance it was not the same.

Quote:

Originally Posted by peleincubus

So was the harness in the OP the wrong one?

It was the correct one as specified by metra however most pins were in the in correct spots to corilate to the factory harness.

Quote:

Originally Posted by coolvans1988

Same here on my Base 2013, i supplied my installer
with the metra harness model 70-7552, no problems.
Headunit, door speakers/tweeters, and metra kit for steering wheel controls.

Used the same items as the earlier 370z models.

took about 2.5 hrs to complete.

Baer383 · 08-01-2013, 03:27 PM

Quote:

Originally Posted by bigaudiofanat

As stated earlier it could be early 2013 models used the older style. However in this instance it was not the same.
.

So you really think that my whole wiring harness is differant than other 2013.

bigaudiofanat · 08-01-2013, 04:56 PM

Quote:

Originally Posted by Baer383

So you really think that my whole wiring harness is differant than other 2013.

Yep

Baer383 · 08-01-2013, 05:01 PM

Quote:

Originally Posted by bigaudiofanat

Yep

You should be blaming Metra before Nissan.

bigaudiofanat · 08-01-2013, 09:07 PM

Quote:

Originally Posted by Baer383

You should be blaming Metra before Nissan.

Never blamed anyone just a fair warning to what I have ran into.

Zteve · 08-04-2013, 12:58 PM

Quote:

Originally Posted by Inda370z

I just finished an install on my 2013 as well. I got the metra harness and just removed the rear speaker pins and placed them in the spots needed for the steering wheel controls. Took me all of 10 minutes. I noticed you went with rear speakers so yeah you would of needed 2. As for the speakers, you are correct, You have to go through a solid grommet.

So for those not using rear speakers, get the metra or scosche harness and just remove the rear speaker pins from the harness and place them into slots to connect pins shown in the attached diagram. You can use a small eyeglass screwdriver to remove the pins, just insert it into the hole above the pin (when looking into the connector) this will give you a clean install with no factory wires being cut. As for ground, just run a line and create your own.

Pioneer x5500bhs and Pioneer components installed

silly question, in the diagram of the pin #'s is that as you are looking into the harness or is that from the wire side? i think it is looking into the harness at the pins because that matches the 7552. if that is the wire side of the OEM harness that would be a good match as well.

maybe i am just over thinking it.

Zteve · 08-09-2013, 04:22 PM

well, thanks to the diagram and all the topics mentioned my install went perfect, no issues at all. even got it all back together just as it started to thunder and pour down rain.

bacalhau1669 · 08-10-2013, 03:17 PM

I actually removed my pioneer double din out of a 2011 WRX and it plugged right into my 2013 Base. All the audio seems to work with no issue as does illumination.

Zteve · 08-15-2013, 07:24 PM

Quote:

Originally Posted by voided

Just to be clear:

The OP stated that all the wires had changed, implying the SWC wires as well. The wiring diagram a few posts down indicates the SWC wires are still 6 and 16 just like before.

Is this correct?

I can't get my Axxess to work even though I've tapped into 6 and 16.

did you ground 15? i made sure i moved one of the rear speaker pins to the 15 slot then grounded it with the radio ground.

bigaudiofanat · 08-16-2013, 09:57 PM

Quote:

Originally Posted by voided

Yes, 15 is grounded. I have it running to the back of my radio harness then up to the body ground. It's basically a 3-way splice.

When I try to program the Axxess (holding Up arrow after reset), instead of going to a solid Red mode, it goes solid Green. At this point the radio starts going beeping constantly as though the SWC is sending a non-stop signal.

I can't get it to work and it's driving me crazy.

What brand head unit are you running?

Zteve · 08-18-2013, 08:45 AM

i had to do the manual programming steps and that worked for all buttons.

killerb87 · 09-02-2013, 08:51 AM

Quote:

Originally Posted by voided

I'm starting to believe I got a defective unit. Metra technical support was useless: rude, impatient, condescending and unhelpful. I packed up my Axxess for return (already got the RMA from Amazon) - I'll either go with a PAC or I'll go without.

I had the same experience with Metra when i told the guy that the wiring harness had changed. He was rude and basically told me I didn't know what I was talking about. I ended up cursing him the f*** out and returning the Axxess to Amazon.

Zteve · 09-02-2013, 09:53 AM

from the metra harness i got from crutchfield with my stereo, there is nothing wrong with that harness and the 2013 base vehicle harness matching. they basically plugged right up and function correctly. the only pins i removed were the rear speakers since i do not have those and used them for the axxess steering wheel control as mentioned earlier in this thread. i also got my axxess from amazon, wired it according to the diagram, did the manual programming, and all buttons work perfectly.

370_o · 12-30-2013, 12:48 AM

I just ran into the same problem as the OP with my Alpine head unit install this weekend. I had to rearrange the pins as previously suggested to make my Metra wire harness work. I'm not sure where that connector diagram previously posted came from but my vehicle side harness, and the service manual I was using, didn't have pin 18. Fair warning to all out there, Amazon is still selling bum connectors.

jooonnn · 12-30-2013, 09:51 AM

my nismo '13 install had no issues other than those dang car side wires for the car side harness being so damn small for tapping when connecting the ASWC. i do have the bose system though

08-09-2013, 04:22 PM	#22 (permalink)
Zteve Enthusiast Member Join Date: Jul 2013 Location: Clarksville TN Posts: 348 Drives: 2013 370Z MB w/Sport Rep Power: 3369	well, thanks to the diagram and all the topics mentioned my install went perfect, no issues at all. even got it all back together just as it started to thunder and pour down rain. nomad likes this. __________________ 2013 Midnight Blue 370Z Base w/Sport Package

08-18-2013, 08:45 AM	#26 (permalink)
Zteve Enthusiast Member Join Date: Jul 2013 Location: Clarksville TN Posts: 348 Drives: 2013 370Z MB w/Sport Rep Power: 3369	i had to do the manual programming steps and that worked for all buttons. __________________ 2013 Midnight Blue 370Z Base w/Sport Package

09-02-2013, 09:53 AM	#28 (permalink)
Zteve Enthusiast Member Join Date: Jul 2013 Location: Clarksville TN Posts: 348 Drives: 2013 370Z MB w/Sport Rep Power: 3369	from the metra harness i got from crutchfield with my stereo, there is nothing wrong with that harness and the 2013 base vehicle harness matching. they basically plugged right up and function correctly. the only pins i removed were the rear speakers since i do not have those and used them for the axxess steering wheel control as mentioned earlier in this thread. i also got my axxess from amazon, wired it according to the diagram, did the manual programming, and all buttons work perfectly. __________________ 2013 Midnight Blue 370Z Base w/Sport Package Last edited by Zteve; 09-02-2013 at 09:55 AM.

12-30-2013, 09:51 AM	#30 (permalink)
jooonnn Enthusiast Member Join Date: Oct 2012 Location: South Carolina Posts: 270 Drives: 2013 Nismo Rep Power: 13	my nismo '13 install had no issues other than those dang car side wires for the car side harness being so damn small for tapping when connecting the ASWC. i do have the bose system though __________________ Try things once to see how it feels. Try things a second time to make sure you didn't like it

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Factory NAV Retrofit Install for Touring Models	scruffydog	Audio & Video	20	11-23-2015 07:16 AM
2013 models still being supplied?	ak8905	Nissan 370Z Pricing / Ordering Discussions	9	03-16-2013 01:13 AM
Did they change the muffler on 2013 models?	MrXistential	Intake/Exhaust	16	03-05-2013 10:00 AM
Word of Caution	Duncanz	Nissan 370Z General Discussions	79	07-06-2010 11:57 AM
Tsb: Various nissan models; i-key registration caution	AK370Z	370Z Technical Service Bulletins (TSB) / Recalls	0	02-08-2010 10:44 PM

08-10-2013, 03:17 PM	#23 (permalink)
bacalhau1669 Base Member Join Date: Jun 2013 Location: palm coast Posts: 86 Drives: 2013 Base Sport Rep Power: 12	I actually removed my pioneer double din out of a 2011 WRX and it plugged right into my 2013 Base. All the audio seems to work with no issue as does illumination.

12-30-2013, 12:48 AM	#29 (permalink)
370_o Base Member Join Date: Jul 2013 Location: Santa Monica, CA Posts: 51 Drives: 2013 370Z Sport M6 Rep Power: 15	I just ran into the same problem as the OP with my Alpine head unit install this weekend. I had to rearrange the pins as previously suggested to make my Metra wire harness work. I'm not sure where that connector diagram previously posted came from but my vehicle side harness, and the service manual I was using, didn't have pin 18. Fair warning to all out there, Amazon is still selling bum connectors.