How To - Power Wire Run from Battery to Rear Hatch Area

a6walter1 · 03-04-2013, 02:58 PM

I looked for many hours on these forums to find a comprehensive guide on how to run the power wire and didnt have any luck, I found the beginning and the end of the wire. So hopefully this guide will help others.

Products - 4AWG Power Wire, Streetwires fuse holder, 80 AMP Fuse, Streetwires 4AWG ring terminals

Step 1 - Mount the fuse holder, I found an empty hole to mount it to.

Step 2 - Cut a length of wire to run from the battery to the fuse holder

Step 3 - Run the wire around the back of the battery and push it through the grommet in the corner of the battery bay.

Step 4 - Feed the wire down the passenger side footwell, be sure to take off the door sil panel and the front quarter panel to run the wire.

Step 5 - Run the wire through the stock wire holder along side the factory harness.

Step 6 - Feed the wire behind the panel that has the rear speaker in it, the wire will come out where the factory harness comes out in the rear hatch area.

Cbtech · 03-04-2013, 05:45 PM

Very cool. I was just going to post a question on how much wire was needed to run from the battery to the center of the hatch. So...how many feet did you need?

a6walter1 · 03-04-2013, 07:12 PM

Quote:

Originally Posted by Cbtech

Very cool. I was just going to post a question on how much wire was needed to run from the battery to the center of the hatch. So...how many feet did you need?

I bought 18 feet, but there is 8 or so extra feet in the rear, so i guess if u wanna be safe go with 15 feet, or if you are daring 12 feet.

TreeSemdyZee · 03-05-2013, 10:40 AM

Never even thought of running mine through the door sill.
Went down the center tunnel, but everything else is pretty much the same.

edconline · 03-08-2013, 08:06 PM

Looking good! Interested to see what you use to attach the power cable to the battery, any ideas on that front yet?

bigaudiofanat · 03-08-2013, 11:24 PM

Quote:

Originally Posted by edconline

Looking good! Interested to see what you use to attach the power cable to the battery, any ideas on that front yet?

All power wire kits come with an O ring for the end, so you can simply remove your battery terminal nut slide the O ring on and tighten it back down. I would only advice moving the fuse holder a little further away from the battery terminal.

a6walter1 · 03-09-2013, 01:11 AM

Quote:

Originally Posted by bigaudiofanat

All power wire kits come with an O ring for the end, so you can simply remove your battery terminal nut slide the O ring on and tighten it back down. I would only advice moving the fuse holder a little further away from the battery terminal.

Why do you think i need to move the fuse holder further away?

a6walter1 · 03-09-2013, 01:12 AM

Quote:

Originally Posted by edconline

Looking good! Interested to see what you use to attach the power cable to the battery, any ideas on that front yet?

Yep i bought some streetwires ring terminals, i will post some pics when it is all hooked up.

bigaudiofanat · 03-10-2013, 11:33 AM

Quote:

Originally Posted by a6walter1

Why do you think i need to move the fuse holder further away?

Just very close to the terminal, the fuse block could eventually start rubbing on the metal of the terminal and short out. I just like to be cautious.

03-04-2013, 02:58 PM	#1 (permalink)
a6walter1 Base Member Join Date: Oct 2011 Location: Dayton, OH Posts: 132 Drives: '12 Z34 PW 7AT Rep Power: 14	How To - Power Wire Run from Battery to Rear Hatch Area I looked for many hours on these forums to find a comprehensive guide on how to run the power wire and didnt have any luck, I found the beginning and the end of the wire. So hopefully this guide will help others. Products - 4AWG Power Wire, Streetwires fuse holder, 80 AMP Fuse, Streetwires 4AWG ring terminals Step 1 - Mount the fuse holder, I found an empty hole to mount it to. Step 2 - Cut a length of wire to run from the battery to the fuse holder Step 3 - Run the wire around the back of the battery and push it through the grommet in the corner of the battery bay. Step 4 - Feed the wire down the passenger side footwell, be sure to take off the door sil panel and the front quarter panel to run the wire. Step 5 - Run the wire through the stock wire holder along side the factory harness. Step 6 - Feed the wire behind the panel that has the rear speaker in it, the wire will come out where the factory harness comes out in the rear hatch area. __________________ My Journal (2012 PW 7AT)

03-08-2013, 08:06 PM	#5 (permalink)
edconline Track Member Join Date: Mar 2010 Location: Edmonton Posts: 855 Drives: 10' MB Z34 6MT T/S/N Rep Power: 23	Looking good! Interested to see what you use to attach the power cable to the battery, any ideas on that front yet? __________________ View Journal Audio Build

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Quick help needed. Speaker wire from hatch.	vermithrax	Audio & Video	1	08-10-2012 05:14 PM
How useable is the rear hatch area in a 370Z?	JulesD	Nissan 370Z General Discussions	72	04-18-2012 10:59 PM
Battery to amp power cable wire routing question	Pat C.	Audio & Video	5	03-10-2012 09:17 PM
370z Rear hatch area floor mat $60 shipped	USMCASA	Parts for sale (Private Classifieds)	2	03-01-2010 02:02 AM

03-04-2013, 05:45 PM	#2 (permalink)
Cbtech A True Z Fanatic Join Date: Feb 2013 Location: Sacramento, CA Posts: 1,372 Drives: 40th Anniversary Rep Power: 16	Very cool. I was just going to post a question on how much wire was needed to run from the battery to the center of the hatch. So...how many feet did you need?

03-05-2013, 10:40 AM	#4 (permalink)
TreeSemdyZee Premium Member Join Date: Dec 2009 Location: Kentuck-IANA Age: 60 Posts: 4,886 Drives: '09 370 & ‘14 Juke Rep Power: 27409	Never even thought of running mine through the door sill. Went down the center tunnel, but everything else is pretty much the same.