Jayhovah's fiberglass sub box build log

RonRizz · 01-07-2018, 10:43 PM

Quote:

Originally Posted by Jayhovah

I have no idea. I am going to wrap the sides with some foam and hope it fits in tightly enough to stay put.

If I anchor it to a panel I'll need to mod the trunk mats to ensure I can access the spare tire.

Please anchor the subs in a solid fashion. A friend of mine had a box in his hatch mounted with Velcro. one night someone ran him off the road into a ditch. He would have came off with barely a scratch if it wasn't for the sub box getting him in the back of the head, which in turn put his face into the steering wheel. Split him open like a ripe watermelon, and pushed 4 teeth through his lower lip... Luckily, he wasn't killed by it.
even if its just a strap to hold it down, for gods sake, make it SOLID.

this is the end of our public service announcement.

Jayhovah · 01-07-2018, 11:25 PM

Quote:

Originally Posted by RonRizz

Please anchor the subs in a solid fashion.

Any ideas on how I might anchor this one?

RonRizz · 01-08-2018, 05:29 AM

At a glance, I'd say I like your idea of using some type of foam or weatherstripping between the box, and plastic trim pieces. Not to hold the sub, but to prevent vibrations between the box and these hard surfaces. As far as mounting, would it be possible to place an L bracket or something similar under the strut bar and into the enclosure? at least there it would not be visible, and if you ever take the box out to "gasp" sell the car, you wouldn't see the screw holes.... of course, I would use a nut and a large fender washer inside the enclosure. I'm thinking a right angle bit to run a self tapper up into bottom of strut bar.

Jayhovah · 01-08-2018, 04:04 PM

Quote:

Originally Posted by RonRizz

At a glance, I'd say I like your idea of using some type of foam or weatherstripping between the box, and plastic trim pieces. Not to hold the sub, but to prevent vibrations between the box and these hard surfaces. As far as mounting, would it be possible to place an L bracket or something similar under the strut bar and into the enclosure? at least there it would not be visible, and if you ever take the box out to "gasp" sell the car, you wouldn't see the screw holes.... of course, I would use a nut and a large fender washer inside the enclosure. I'm thinking a right angle bit to run a self tapper up into bottom of strut bar.

That's a pretty good idea... Maybe with a wingnut so that removal does not require tools in the event I need to get to the spare. I will have to think about how I might best secure it.

No worries about ever selling the car... I've got way too much money/blood/sweat/tears into it to ever let it go.

OldGrayDog · 01-08-2018, 06:12 PM

Not sure if my mounting method would help.

I mounted an infinity all inone subamp , by making long u shaped brackets that went under/around one edge and kind of pinched the mats and honey comb plastic support. I then screwed the sub into top of the alluminum u bracket.

If I need to get underneath, I pull up and tilt the mats and slide the sub with brackets off.

Jayhovah · 01-08-2018, 08:36 PM

Quote:

Originally Posted by OldGrayDog

Not sure if my mounting method would help.

I mounted an infinity all inone subamp , by making long u shaped brackets that went under/around one edge and kind of pinched the mats and honey comb plastic support. I then screwed the sub into top of the alluminum u bracket.

If I need to get underneath, I pull up and tilt the mats and slide the sub with brackets off.

This sounds interesting but I am having a difficult time visualizing it... Would you be willing to take a couple of pictures?

BoneZ · 01-08-2018, 08:43 PM

Put a screw right to the bottom of the box into the middle of the car.

Jayhovah · 01-08-2018, 08:51 PM

Quote:

Originally Posted by BoneZ

Put a screw right to the bottom of the box into the middle of the car.

You might be on to something though - I was actually thinking about the stud/bolt ends sticking up from the floor under that foam plug... Could couple a threaded rod to one of those to come up and mount the enclosure to if its placed well enough.

BoneZ · 01-08-2018, 08:59 PM

Quote:

Originally Posted by Jayhovah

You might be on to something though - I was actually thinking about the stud/bolt ends sticking up from the floor under that foam plug... Could couple a threaded rod to one of those to come up and mount the enclosure to if its placed well enough.

That could work.

OldGrayDog · 01-08-2018, 09:41 PM

Quote:

Originally Posted by Jayhovah

This sounds interesting but I am having a difficult time visualizing it... Would you be willing to take a couple of pictures?

Ill get some pics and post, but think of a pair of large money clips that slide on to rear mats, and you then mount the sub to from the top.

axmea? · 01-08-2018, 10:01 PM

I welded two bolts on one if my installs and used a metal strap to anchor it down. Siliconed the strap afterwards.

Jayhovah · 01-09-2018, 10:21 AM

Quote:

Originally Posted by axmea?

I welded two bolts on one if my installs and used a metal strap to anchor it down. Siliconed the strap afterwards.

I have no welding skills... but....pics? =)

OldGrayDog · 01-09-2018, 06:30 PM

Quote:

Originally Posted by OldGrayDog

Ill get some pics and post, but think of a pair of large money clips that slide on to rear mats, and you then mount the sub to from the top.

Here are a pair of snapshots. Because of where you are mounting , you would need smaller brackets, on two sides maybe.

From the side you can see the shape

How the lower part of bracket slides under the carpet, like a money clip

Jayhovah · 01-09-2018, 11:56 PM

Quote:

Originally Posted by OldGrayDog

Here are a pair of snapshots. Because of where you are mounting , you would need smaller brackets, on two sides maybe.

Thanks! Not sure its for me, but that is a pretty slick idea!

Jayhovah · 01-10-2018, 12:03 AM

I coated the inside with the milkshake concoction that I am choosing to call the "Milk BoneZ".

I went with a 2:1 ratio of resin to filler and it seemed thick enough to coat but runny enough to move around the inside. If I did it again I might make it just a bit thicker.

I'll find out tomorrow if it made the difference!

01-08-2018, 05:29 AM	#63 (permalink)
RonRizz A True Z Fanatic Join Date: Aug 2011 Location: Pine grove, Pa Posts: 2,136 Drives: 2 feet, 3 pedals Rep Power: 6775	At a glance, I'd say I like your idea of using some type of foam or weatherstripping between the box, and plastic trim pieces. Not to hold the sub, but to prevent vibrations between the box and these hard surfaces. As far as mounting, would it be possible to place an L bracket or something similar under the strut bar and into the enclosure? at least there it would not be visible, and if you ever take the box out to "gasp" sell the car, you wouldn't see the screw holes.... of course, I would use a nut and a large fender washer inside the enclosure. I'm thinking a right angle bit to run a self tapper up into bottom of strut bar. Jayhovah likes this. __________________ P99rs Head Unit--- Amps- 2 Pioneer Prs800d --- Zapco ST1000MX---Zapco ST-4XSQ---- SI BM mk5 Subs---SI TM65v2 Midbass--- SI M3 mids--- SI M25 xbl2 tweeters ----- 2016 MECA street class 3rd place at world finals

01-08-2018, 06:12 PM	#65 (permalink)
OldGrayDog Base Member Join Date: Jan 2017 Location: Pa VF Posts: 108 Drives: 14 370z at7 GM Rep Power: 597	Not sure if my mounting method would help. I mounted an infinity all inone subamp , by making long u shaped brackets that went under/around one edge and kind of pinched the mats and honey comb plastic support. I then screwed the sub into top of the alluminum u bracket. If I need to get underneath, I pull up and tilt the mats and slide the sub with brackets off. Jayhovah likes this.

01-08-2018, 08:43 PM	#67 (permalink)
BoneZ A True Z Fanatic Join Date: May 2015 Location: Atlanta, GA Age: 52 Posts: 9,299 Drives: 2012 Blue BallZ Rep Power: 2684382	Put a screw right to the bottom of the box into the middle of the car. Jayhovah likes this. __________________ *“Happiness is having a large, loving, caring, close-knit family in another city.”*-George Burns

01-08-2018, 10:01 PM	#71 (permalink)
axmea? A True Z Fanatic Join Date: Apr 2012 Location: SoCal Posts: 6,235 Drives: WELL ZED PW 6MT Rep Power: 53241	I welded two bolts on one if my installs and used a metal strap to anchor it down. Siliconed the strap afterwards. __________________ >MyZ's Album< NISMO Convert/ECUTEK/Takeda CAI/F.I. HFC NR CB Carbon/F.I. 34 Row Oil Cooler/4.08 Final Drive /Powertrix+Swifts/Hotchkis/SPL/Whiteline/TWM/Zoom Engineering/EVO-R/AeroJacket Vented CF Fenders + CF Spoiler/Avant Garde-WORK/NST/Morimoto Halo/STi Clear Lenses/Carbon Signal Automotive/RJM Performance/ZSpeed Clutch Flywheel CSC delete

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Jayhovah's Gamma V3 TT Install Pic/Video Dump	Jayhovah	Forced Induction	25	05-14-2017 09:37 AM
Jayhovah's Build Journal	Jayhovah	Member's 370Z Gallery	13	10-30-2014 02:42 PM
Custom Fiberglass Sub Box	CSA0890	Audio & Video	0	11-26-2012 11:06 PM
fiberglass box	im89	Audio & Video	7	02-04-2011 04:57 PM