Stereo rebuild

DeliriousClam · 06-20-2016, 05:12 PM

As far as the antenna connection goes, untwist them. There should be one that's just copper wire strands and the other should be copper wire, some kind of shielding, then a single wire in the center of the shielding. The one that is just copper wire strands is your power antenna line. The one with the shielding in it is the actual antenna connection

DeliriousClam · 06-20-2016, 05:17 PM

This is kind of what the antenna signal wire should look like. (Yes I sacrificed an antenna adapter for this picture.)

white37014 · 06-22-2016, 12:22 PM

wow looks good man you sure had your work cut out for you on this one, looks like the project is coming along nicely, I once had a disaster of a wire issue on a RSX I bought from somebody what a mess!

370ZBlk · 06-22-2016, 12:43 PM

I just replaced the following;

Stock headunit for Pioneer HU W/ Car Play
Steering Wheel Controls
Rear View Camera
Wired all of this to the factory BOSE, for now.

Next goal is to add a aftermarket subwoofer in a custom enclosure w/ standalone amp and dynamat the trunk. .

Question: How easy was it for you to dynamat the trunk? How much material was needed? I also plan to dynamat the hatch as well.

Thanks!

*Edited - damn autocorrect lol.

DeliriousClam · 06-22-2016, 12:45 PM

Quote:

Originally Posted by 370ZBlk

I just replaced the following;

Stock headunit for Pioneer HU W/ Car Play
Steering Wheel Controls
Rear View Camera
Wired all of this to the factory BOSE, for now.

Next goal is to add a aftermarket subwoofer in a custom enclosure w/ standalone amp and dynamite the trunk. .

Question: How easy was it for you to dynamite the trunk? How much material was needed? I also plan to dynamite the hatch as well.

Thanks!

Adding dynamite to the trunk sounds dangerous. You trying to go full Pinto?

370ZBlk · 06-22-2016, 01:22 PM

Quote:

Originally Posted by DeliriousClam

Adding dynamite to the trunk sounds dangerous. You trying to go full Pinto?

DeliriousClam · 06-22-2016, 01:49 PM

In all seriousness though, dynamat is easy. You don't have to make it look good because it won't be seen. Cut it, lay it down, press it down, then press it down with the round end of a handle on a screwdriver (or a roller if you buy one for doing it) in the corners and grooves and ****

NorthStyle · 06-22-2016, 05:24 PM

Quote:

Originally Posted by white37014

wow looks good man you sure had your work cut out for you on this one, looks like the project is coming along nicely, I once had a disaster of a wire issue on a RSX I bought from somebody what a mess!

Yeah, I just finished up fixing the rest of the wiring this afternoon after work. The antenna was a bit of a pain being a coaxial cable so what I did was solder the innermost strands, wrap them in foil (no clue, but looked similar to what was already there so I was going for uniformity lol), then wrap them in more copper cable from some multi-strand wiring I had then wrap that in electrical tape as I had forgot to run the heatshrink tubing beforehand. All-in-all, came out well and everything "stereo-wise" works as it should.

Quote:

Originally Posted by 370ZBlk

I just replaced the following;

Stock headunit for Pioneer HU W/ Car Play
Steering Wheel Controls
Rear View Camera
Wired all of this to the factory BOSE, for now.

Next goal is to add a aftermarket subwoofer in a custom enclosure w/ standalone amp and dynamat the trunk. .

Question: How easy was it for you to dynamat the trunk? How much material was needed? I also plan to dynamat the hatch as well.

Thanks!

*Edited - damn autocorrect lol.

Pretty much the same as everything I've done. The only issues I'm having are the reverse camera not turning on when I engage reverse and not being able to fully setup the Axxess as it won't recognize my Search up or down buttons (harness was made by bigaudiofanat and double- and triple-checked the wiring so there may be something wrong with my module). Minor things but still annoying considering how much BS I've already gone through...

As for the sound deadener, I used RAAM Mat and like DeliriousClam said, it's extremely easy to apply... just tedious and time-consuming. I just ordered the $159~ish setup and I still have a bit leftover to do in front of the rear shock towers and hatch cover but it'll be close.

Quote:

Originally Posted by DeliriousClam

In all seriousness though, dynamat is easy. You don't have to make it look good because it won't be seen. Cut it, lay it down, press it down, then press it down with the round end of a handle on a screwdriver (or a roller if you buy one for doing it) in the corners and grooves and ****

Yupper... invest in a roller. I was able to pick up a pair (small and medium) for 7 Euro and it was much better than patting everything down. I used the end of my scissors for the small edges.

Back to the struggle: As I mentioned previously, I'm having issues with the receiver recognizing the rearview camera so it's either something wrong with the camera or my wiring is wrong. For those of you with an aftermarket camera (I have the type that integrates into the license plate lights), how did you wire it up?

Additionally, I'm unable to get my Axxess configured. I'm able to get as far as setting it up manually, with it recognizing the volume up and volume down, but when I try to set the scan/search up or down I get no lights... any advice? Thanks again.

370ZBlk · 06-22-2016, 08:39 PM

Quote:

Originally Posted by NorthStyle

Pretty much the same as everything I've done. The only issues I'm having are the reverse camera not turning on when I engage reverse and not being able to fully setup the Axxess as it won't recognize my Search up or down buttons (harness was made by bigaudiofanat and double- and triple-checked the wiring so there may be something wrong with my module). Minor things but still annoying considering how much BS I've already gone through...

Funny I had the same two issues..

1) For the rear verse camera - I did the following. Behind the headunit you should have a wire that says reverse camera input, and take the positive of the rear camera wire and connect it to that.. Taking the same positive wire, connect it to the positive wite of the reverse light within the tail lights.. The negative gets connected to a ground (I connected it at the rear where a bunch of grounds were).. For the camera have dedicated positive and negative wire rather than a negative that is coiled which was my problem originally. The RCA cable goes into the port for the reverse camera. This solved my problem.

2) For the AXXIS - my search up and down works, but not on Apple Car Play. It works on the radio only.. So I know the function works but not working on specific application. My source doesnt work but instead it mutes the sound to a lower volume - which works wonders.

As for the sound deadener, I used RAAM Mat and like DeliriousClam said, it's extremely easy to apply... just tedious and time-consuming. I just ordered the $159~ish setup and I still have a bit leftover to do in front of the rear shock towers and hatch cover but it'll be close.

Thanks for the info!

Yupper... invest in a roller. I was able to pick up a pair (small and medium) for 7 Euro and it was much better than patting everything down. I used the end of my scissors for the small edges.

Back to the struggle: As I mentioned previously, I'm having issues with the receiver recognizing the rearview camera so it's either something wrong with the camera or my wiring is wrong. For those of you with an aftermarket camera (I have the type that integrates into the license plate lights), how did you wire it up?

Additionally, I'm unable to get my Axxess configured. I'm able to get as far as setting it up manually, with it recognizing the volume up and volume down, but when I try to set the scan/search up or down I get no lights... any advice? Thanks again.

Replies in red.

NorthStyle · 06-23-2016, 12:38 AM

Much apprecated, I'll check that out!!

bigaudiofanat · 06-23-2016, 07:54 AM

Do you have any picks of the actually harness wired up? I see the wires not the harness.

NorthStyle · 06-23-2016, 08:59 AM

Quote:

Originally Posted by bigaudiofanat

Do you have any picks of the actually harness wired up? I see the wires not the harness.

Yeah, I guess I didn't take any lol. I'll get some for you once I'm off work since I'll be back at it trying to setup the Axxess and double check all of the connections for the camera.

Any idea on why the Axxess is only recognizing the volume up/down but not the search up/down function when configuring it? The speakers and amp are working fine (haven't done the sub since the hatch is still apart) although I still need to properly setup the amp once I have everything buttoned up.

bigaudiofanat · 06-23-2016, 12:20 PM

Quote:

Originally Posted by NorthStyle

Yeah, I guess I didn't take any lol. I'll get some for you once I'm off work since I'll be back at it trying to setup the Axxess and double check all of the connections for the camera.

Any idea on why the Axxess is only recognizing the volume up/down but not the search up/down function when configuring it? The speakers and amp are working fine (haven't done the sub since the hatch is still apart) although I still need to properly setup the amp once I have everything buttoned up.

Yep, know exactly why. Can't do auto program you have to do manual. fallow my youtube video.

DeliriousClam · 06-23-2016, 12:23 PM

Quote:

Originally Posted by bigaudiofanat

Yep, know exactly why. Can't do auto program you have to do manual. fallow my youtube video.

This is why I personally prefer the Maestro SW

bigaudiofanat · 06-23-2016, 12:36 PM

Quote:

Originally Posted by DeliriousClam

This is why I personally prefer the Maestro SW

True but way more expensive. It would be like putting in a computer to do a pda's job.

06-20-2016, 05:12 PM	#16 (permalink)
DeliriousClam A True Z Fanatic Join Date: May 2015 Location: NJ Age: 31 Posts: 3,758 Drives: 12 Base Sport Rep Power: 54272	As far as the antenna connection goes, untwist them. There should be one that's just copper wire strands and the other should be copper wire, some kind of shielding, then a single wire in the center of the shielding. The one that is just copper wire strands is your power antenna line. The one with the shielding in it is the actual antenna connection __________________ Stillen, AAM, Shine Auto, Fujimora, Swift, EVO-R, Carbon Fiber Element, Nitrous Outlet MECP Advanced: CEA26671 Most of what I post here are artistic works of fiction and falsehood. Only a fool would take anything I post here as fact. Last edited by DeliriousClam; 06-20-2016 at 05:18 PM.

06-22-2016, 12:43 PM	#19 (permalink)
370ZBlk Base Member Join Date: Mar 2016 Location: GA, USA Posts: 53 Drives: 370Z Rep Power: 9	I just replaced the following; Stock headunit for Pioneer HU W/ Car Play Steering Wheel Controls Rear View Camera Wired all of this to the factory BOSE, for now. Next goal is to add a aftermarket subwoofer in a custom enclosure w/ standalone amp and dynamat the trunk. . Question: How easy was it for you to dynamat the trunk? How much material was needed? I also plan to dynamat the hatch as well. Thanks! Edited - damn autocorrect lol. __________________ -14 MB 370Z Touring Sport 6MT- Last edited by 370ZBlk; 06-22-2016 at 01:21 PM.*

06-22-2016, 01:49 PM	#22 (permalink)
DeliriousClam A True Z Fanatic Join Date: May 2015 Location: NJ Age: 31 Posts: 3,758 Drives: 12 Base Sport Rep Power: 54272	In all seriousness though, dynamat is easy. You don't have to make it look good because it won't be seen. Cut it, lay it down, press it down, then press it down with the round end of a handle on a screwdriver (or a roller if you buy one for doing it) in the corners and grooves and **** 370ZBlk likes this. __________________ Stillen, AAM, Shine Auto, Fujimora, Swift, EVO-R, Carbon Fiber Element, Nitrous Outlet MECP Advanced: CEA26671 Most of what I post here are artistic works of fiction and falsehood. Only a fool would take anything I post here as fact.

06-23-2016, 07:54 AM	#26 (permalink)
bigaudiofanat Car Audio Installer Join Date: Jun 2009 Location: Magnolia DE Posts: 8,342 Drives: 2012 Infiniti G37x Rep Power: 853	Do you have any picks of the actually harness wired up? I see the wires not the harness. __________________ Need help with car audio or electronics? Let me know!! Need Help Let Me Know Direct email address reimermatt@gmail.com Owner of: Dynamic Mobile Audio Follow me below https://www.facebook.com/Dynamicmobileaudio/

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Rebuild vs Replace	jwomack1547	Engine & Drivetrain	4	10-08-2015 11:41 AM
N/A Rebuild	SharkBite	Tuning	33	06-09-2015 02:56 AM
KW coilover rebuild?	corbin09	Brakes & Suspension	0	05-30-2012 04:22 PM
if you rebuild it, um.. they will come.	Danny3.7	The Lounge (Off Topic)	23	11-02-2010 01:19 AM

06-22-2016, 12:22 PM	#18 (permalink)
white37014 Base Member Join Date: May 2014 Location: Pa Posts: 114 Drives: 14 370 base sport 6t Rep Power: 11	wow looks good man you sure had your work cut out for you on this one, looks like the project is coming along nicely, I once had a disaster of a wire issue on a RSX I bought from somebody what a mess!

06-23-2016, 12:38 AM	#25 (permalink)
NorthStyle A True Z Fanatic Join Date: Aug 2015 Location: Deutschland + SC/FL USA Posts: 1,255 Drives: 2011 370Z Nismo Rep Power: 24277	Much apprecated, I'll check that out!!