Molex Removal?

SlikNik · 10-15-2009, 12:20 PM

I did a quick search and didn't comeup with much. My question is I have my door molex to this point.

How do I remove it from this point? I have the lever unclipped and folded back, I wiggled a bit but it doesn't seem to want to unclip.

Any ideas?

pg6speed · 10-15-2009, 01:21 PM

pull the lever down farther

SlikNik · 10-15-2009, 01:24 PM

Quote:

Originally Posted by pg6speed

pull the lever down farther

It hits the door, all the way down I believe

Division · 10-15-2009, 01:45 PM

close the door *slightly* you can pull it off. (I did this in my car, I know- have a friend help if you don't want your hand crushed)

Once you have it off, you have to pull out the other side of the connector from inside the car. Grab an exacto knife and carefully cut out the UNUSED plastic part at the top of the connector, you can run your wires through there fine.

SlikNik · 10-15-2009, 01:48 PM

Damn, I just went out and closed the door some and WHAMMO I was able to pull lever all the way down. It practically fell out.

You guys rock

SlikNik · 10-15-2009, 05:59 PM

Once removed it is easy to unhook the female connector and drill out a hole in the connector to run 12 guage through. The fun part is running the wire through the rubber hose and then reconnecting the oh so fun Molex back together without it clicking open all the way or closing before you get the two connectors together. Did drivers side first and finally got it which made the passendger side go quicker. The big difference on the pass. side is the Molex connector pin faces the opposite way and you can't get at the opening to stick a eye glass screw driver in there. So it took me a little bit to figure out how to disconnect.

Glad to be moving on to the next step. I had to suck down a Sam Adams after that

bigaudiofanat · 10-15-2009, 07:14 PM

You can do that but me I just used the stock wiring. That is stable up until 65 watts.

Division · 10-15-2009, 09:25 PM

Quote:

Originally Posted by SlikNik

Damn, I just went out and closed the door some and WHAMMO I was able to pull lever all the way down. It practically fell out.

You guys rock

Glad to help.

SlikNik · 10-16-2009, 06:21 AM

Quote:

Originally Posted by bigaudiofanat

You can do that but me I just used the stock wiring. That is stable up until 65 watts.

I will have more than 65 watts rms with the Jl Audio HD 900/5 amp.

10-15-2009, 12:20 PM	#1 (permalink)
SlikNik Enthusiast Member Join Date: May 2009 Location: Florida Posts: 294 Drives: 2015 Corvette Z51 Rep Power: 18	Molex Removal? I did a quick search and didn't comeup with much. My question is I have my door molex to this point. How do I remove it from this point? I have the lever unclipped and folded back, I wiggled a bit but it doesn't seem to want to unclip. Any ideas?

10-15-2009, 07:14 PM	#7 (permalink)
bigaudiofanat Car Audio Installer Join Date: Jun 2009 Location: Magnolia DE Posts: 8,342 Drives: 2012 Infiniti G37x Rep Power: 853	You can do that but me I just used the stock wiring. That is stable up until 65 watts. __________________ Need help with car audio or electronics? Let me know!! Need Help Let Me Know Direct email address reimermatt@gmail.com Owner of: Dynamic Mobile Audio Follow me below https://www.facebook.com/Dynamicmobileaudio/

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: Headlight Removal	DIGItonium	DIY Section (Do-It-Yourself)	34	09-03-2017 09:01 PM
Best bug removal product?	FlashBazbo	Nissan 370Z General Discussions	40	08-24-2009 08:55 PM
help with gum removal	thispecialk	Nissan 370Z General Discussions	7	08-05-2009 11:41 AM
shock removal	racerxj17	Brakes & Suspension	10	06-11-2009 07:25 PM

10-15-2009, 01:21 PM	#2 (permalink)
pg6speed Base Member Join Date: Jul 2009 Location: San Antonio Posts: 223 Drives: 10 Armada Rep Power: 16	pull the lever down farther

10-15-2009, 01:45 PM	#4 (permalink)
Division Base Member Join Date: Jul 2009 Location: Central FL Posts: 199 Drives: 2009 370Z Sport Rep Power: 16	close the door slightly you can pull it off. (I did this in my car, I know- have a friend help if you don't want your hand crushed) Once you have it off, you have to pull out the other side of the connector from inside the car. Grab an exacto knife and carefully cut out the UNUSED plastic part at the top of the connector, you can run your wires through there fine.

10-15-2009, 01:48 PM	#5 (permalink)
SlikNik Enthusiast Member Join Date: May 2009 Location: Florida Posts: 294 Drives: 2015 Corvette Z51 Rep Power: 18	Damn, I just went out and closed the door some and WHAMMO I was able to pull lever all the way down. It practically fell out. You guys rock

10-15-2009, 05:59 PM	#6 (permalink)
SlikNik Enthusiast Member Join Date: May 2009 Location: Florida Posts: 294 Drives: 2015 Corvette Z51 Rep Power: 18	Once removed it is easy to unhook the female connector and drill out a hole in the connector to run 12 guage through. The fun part is running the wire through the rubber hose and then reconnecting the oh so fun Molex back together without it clicking open all the way or closing before you get the two connectors together. Did drivers side first and finally got it which made the passendger side go quicker. The big difference on the pass. side is the Molex connector pin faces the opposite way and you can't get at the opening to stick a eye glass screw driver in there. So it took me a little bit to figure out how to disconnect. Glad to be moving on to the next step. I had to suck down a Sam Adams after that