Advice for speaker/sub/amp selection

2fast4thelaw · 10-19-2009, 08:15 AM

I wouldnt do it if you are amplifying the signal to the speakers. The stock wire will be inadequate, its only 20 ga. If you are running from deck power than yes, you can wire directly to the crossover from the harness. The crossovers in the stock tweeters are glued to the tweeter.

teejnut · 10-19-2009, 11:09 AM

Quote:

Originally Posted by 2fast4thelaw

I wouldnt do it if you are amplifying the signal to the speakers. The stock wire will be inadequate, its only 20 ga. If you are running from deck power than yes, you can wire directly to the crossover from the harness. The crossovers in the stock tweeters are glued to the tweeter.

hmm... i guess drilling doesn't very appealing! haha. i'm still thinking about it. for drilling i would just need to drill a hole in the side of the door not the body? how do you guys normally seal the hole back up?

teejnut · 10-19-2009, 11:11 AM

oh and if anyone is interested in the kenwood 6140, 6ave.com is having a promotion where you name your price. you can get it for $689, no tax (for me) + free shipping. they are an authorized kenwood dealer per kenwood's website and the reviews for 6ave.com are pretty good from what i saw.

bigaudiofanat · 10-19-2009, 11:14 AM

No normally we take the harness out of the door the rubber hose looking thing, if it is hallow than great just fish it threw if not we have to figure out were to drill threw the plastic connector on both sides. If you are running anything over 50 watts RMS than I would upgrade other than that you will be fine. I use 50 watts on stock wires all the time. Some people will tell you that it can not handle it and all but the fact is it can very well handle it. Because even when running at full volume you still have adjusted your gain on the amp so your are really never going to see 50 watts RMS.

Division · 10-19-2009, 11:34 AM

Quote:

Originally Posted by teejnut

hmm... i guess drilling doesn't very appealing! haha. i'm still thinking about it. for drilling i would just need to drill a hole in the side of the door not the body? how do you guys normally seal the hole back up?

The door connectors are easily removed (pull down the gray hinged tab, and close the door slightly to pop the connector off). On the Base model (sans Bose), the connector on the door side has an opening to run the speaker wire. The connector on the body side will need to be trimmed out, to allow the wires to pass through. It takes about 30 seconds with an exacto knife to make this happen. Much better than using the stock wires.

teejnut · 10-19-2009, 12:06 PM

Quote:

Originally Posted by Division

The door connectors are easily removed (pull down the gray hinged tab, and close the door slightly to pop the connector off). On the Base model (sans Bose), the connector on the door side has an opening to run the speaker wire. The connector on the body side will need to be trimmed out, to allow the wires to pass through. It takes about 30 seconds with an exacto knife to make this happen. Much better than using the stock wires.

that sounds easier then what I was expecting. i wish someone had pics though. I'll attempt to do this then, hopefully next next weekend. Need to order the rest of my stuff.

any opinion on this installation kit? Kicker CK44 (05ck44) 4 Gauge Amp Kits Amplifier Wiring Kits Car Amplifier Installation & Accessories Car Audio/Video Installation & Accessories Car Audio, Video, & GPS Navigation - Sonic Electronix

bigaudiofanat · 10-19-2009, 12:23 PM

That is the stuff I swear by. You will love how flexible it is. Get it it is the best IMO

teejnut · 10-19-2009, 01:09 PM

Quote:

Originally Posted by bigaudiofanat

That is the stuff I swear by. You will love how flexible it is. Get it it is the best IMO

the 16g speaker wire is sufficient for my setup?

Kenwood DNX6140
Focal Access 165A1
IDQ12V2.D2 - Image Dynamics 12" IDQ Dual 2 Ohm Subwoofer
Alpine PDX4.100

Sigur · 10-19-2009, 07:54 PM

Is the factory wiring really 20 guage? Thats frickin' tiny. Not sure I'd use that with any kind of amp driving 4 ohm speakers.

Some info here:

Speaker Cable Gauge (AWG) Guidelines & Recommendations — Reviews and News from Audioholics

bigaudiofanat · 10-19-2009, 08:46 PM

I have done plenty of installs with 50 watts going threw 20 and 18 gauge wire. Works just fine. But yes that 16 will work just fine.

teejnut · 10-20-2009, 12:05 AM

So I ended up ordering the Alpine PDX-4.100. Got it for only $298 from 6ave.com through their current promotion that I mentioned earlier!

2fast4thelaw · 10-20-2009, 10:40 AM

That is a good amplifier and a great price on it too. I need to upgrade my old Alpine V-12's in my Armada so I might pick one up.

bigaudiofanat · 10-20-2009, 11:38 AM

Congrats on the new amp man you will like it.

370Zsteve · 10-20-2009, 11:44 AM

Quote:

Originally Posted by bigaudiofanat

No normally we take the harness out of the door the rubber hose looking thing, if it is hallow than great just fish it threw if not we have to figure out were to drill threw the plastic connector on both sides. If you are running anything over 50 watts RMS than I would upgrade other than that you will be fine. I use 50 watts on stock wires all the time. Some people will tell you that it can not handle it and all but the fact is it can very well handle it. Because even when running at full volume you still have adjusted your gain on the amp so your are really never going to see 50 watts RMS.

As usual Matt is correct. One of the biggest overkills is Monster Cable, etc. A couple of years back Audiophile (or maybe Stereo Review) ran a test of speaker wire. Plain old lamp cord performed as well as many of the "boutique" cables.

Sigur · 10-20-2009, 01:47 PM

I think I'll run some new 16 guage. I plan on running 150wrms into my 3ohm Boston z6's. Plus I don't think the crossovers on those things will fit in the kicks or doors. They are the size of bricks.

10-19-2009, 08:15 AM	#46 (permalink)
2fast4thelaw Enthusiast Member Join Date: Feb 2009 Location: Denver Co Age: 50 Posts: 403 Drives: 09 370Z Sport/MT6 Rep Power: 17	I wouldnt do it if you are amplifying the signal to the speakers. The stock wire will be inadequate, its only 20 ga. If you are running from deck power than yes, you can wire directly to the crossover from the harness. The crossovers in the stock tweeters are glued to the tweeter. __________________ To the optimist, the glass is half full. To the pessimist, the glass is half empty. To the engineer, the glass is twice as big as it needs to be. Last edited by 2fast4thelaw; 10-19-2009 at 08:19 AM.

10-19-2009, 11:14 AM	#49 (permalink)
bigaudiofanat Car Audio Installer Join Date: Jun 2009 Location: Magnolia DE Posts: 8,342 Drives: 2012 Infiniti G37x Rep Power: 853	No normally we take the harness out of the door the rubber hose looking thing, if it is hallow than great just fish it threw if not we have to figure out were to drill threw the plastic connector on both sides. If you are running anything over 50 watts RMS than I would upgrade other than that you will be fine. I use 50 watts on stock wires all the time. Some people will tell you that it can not handle it and all but the fact is it can very well handle it. Because even when running at full volume you still have adjusted your gain on the amp so your are really never going to see 50 watts RMS. __________________ Need help with car audio or electronics? Let me know!! Need Help Let Me Know Direct email address reimermatt@gmail.com Owner of: Dynamic Mobile Audio Follow me below https://www.facebook.com/Dynamicmobileaudio/

10-19-2009, 12:23 PM	#52 (permalink)
bigaudiofanat Car Audio Installer Join Date: Jun 2009 Location: Magnolia DE Posts: 8,342 Drives: 2012 Infiniti G37x Rep Power: 853	That is the stuff I swear by. You will love how flexible it is. Get it it is the best IMO __________________ Need help with car audio or electronics? Let me know!! Need Help Let Me Know Direct email address reimermatt@gmail.com Owner of: Dynamic Mobile Audio Follow me below https://www.facebook.com/Dynamicmobileaudio/

10-19-2009, 08:46 PM	#55 (permalink)
bigaudiofanat Car Audio Installer Join Date: Jun 2009 Location: Magnolia DE Posts: 8,342 Drives: 2012 Infiniti G37x Rep Power: 853	I have done plenty of installs with 50 watts going threw 20 and 18 gauge wire. Works just fine. But yes that 16 will work just fine. __________________ Need help with car audio or electronics? Let me know!! Need Help Let Me Know Direct email address reimermatt@gmail.com Owner of: Dynamic Mobile Audio Follow me below https://www.facebook.com/Dynamicmobileaudio/

10-20-2009, 10:40 AM	#57 (permalink)
2fast4thelaw Enthusiast Member Join Date: Feb 2009 Location: Denver Co Age: 50 Posts: 403 Drives: 09 370Z Sport/MT6 Rep Power: 17	That is a good amplifier and a great price on it too. I need to upgrade my old Alpine V-12's in my Armada so I might pick one up. __________________ To the optimist, the glass is half full. To the pessimist, the glass is half empty. To the engineer, the glass is twice as big as it needs to be.

10-19-2009, 11:11 AM	#48 (permalink)
teejnut Base Member Join Date: Sep 2009 Location: Burbank, CA Posts: 206 Drives: 09 Z34 Sport/6MT Rep Power: 16	oh and if anyone is interested in the kenwood 6140, 6ave.com is having a promotion where you name your price. you can get it for $689, no tax (for me) + free shipping. they are an authorized kenwood dealer per kenwood's website and the reviews for 6ave.com are pretty good from what i saw.

10-19-2009, 07:54 PM	#54 (permalink)
Sigur Base Member Join Date: Sep 2009 Location: Houston, TX Posts: 92 Drives: 09 370Z BS M6 Rep Power: 16	Is the factory wiring really 20 guage? Thats frickin' tiny. Not sure I'd use that with any kind of amp driving 4 ohm speakers. Some info here: Speaker Cable Gauge (AWG) Guidelines & Recommendations — Reviews and News from Audioholics

10-20-2009, 12:05 AM	#56 (permalink)
teejnut Base Member Join Date: Sep 2009 Location: Burbank, CA Posts: 206 Drives: 09 Z34 Sport/6MT Rep Power: 16	So I ended up ordering the Alpine PDX-4.100. Got it for only $298 from 6ave.com through their current promotion that I mentioned earlier!

10-20-2009, 11:38 AM	#58 (permalink)
bigaudiofanat Car Audio Installer Join Date: Jun 2009 Location: Magnolia DE Posts: 8,342 Drives: 2012 Infiniti G37x Rep Power: 853	Congrats on the new amp man you will like it. __________________ Need help with car audio or electronics? Let me know!! Need Help Let Me Know Direct email address reimermatt@gmail.com Owner of: Dynamic Mobile Audio Follow me below https://www.facebook.com/Dynamicmobileaudio/

10-20-2009, 01:47 PM	#60 (permalink)
Sigur Base Member Join Date: Sep 2009 Location: Houston, TX Posts: 92 Drives: 09 370Z BS M6 Rep Power: 16	I think I'll run some new 16 guage. I plan on running 150wrms into my 3ohm Boston z6's. Plus I don't think the crossovers on those things will fit in the kicks or doors. They are the size of bricks.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Speaker Spacers	Mike@ZE	ZEnclosures	22	01-28-2012 07:03 PM
Speaker Size	370book	Audio & Video	44	05-18-2010 10:42 PM
Speaker Wiring	bpd138	Audio & Video	24	09-04-2009 02:36 PM
Speaker/Amp Choices	MacDaddy	Audio & Video	4	07-06-2009 10:35 AM
Rear Speaker/Sub Box	zero610	Audio & Video	19	05-29-2009 07:27 AM