![]() |
Touble codes on my 2010 370z Can anyone help out on this, My Z is in Limp mode. I have changed out computer for the VVEL, still an issue I
|
![]() |
|
LinkBack | Thread Tools | Display Modes |
![]() |
#1 (permalink) |
Base Member
Join Date: Apr 2021
Location: Kentucky
Posts: 2
Drives: 2010 370z White auto
Rep Power: 4 ![]() |
![]()
Touble codes on my 2010 370z
Can anyone help out on this, My Z is in Limp mode. I have changed out computer for the VVEL, still an issue I see I am having issues with communications U1000 CAN communications Line Signal Malfunction M56_AT U1003 Lost Communications with VVEL control Module P1606 VVEL Control Module Malfunction P1421 Cold Start Control I have taken out and cleaned each fuse and relay under the hood as well with electrical cleaner. Does any one have the 370z grounds diagram? Last edited by ZGhost!; 06-21-2021 at 02:12 PM. |
![]() |
![]() |
![]() |
#2 (permalink) |
Premium Member
![]() Join Date: Nov 2010
Location: South Arkansas
Posts: 8,435
Drives: 2014 Challenger
Rep Power: 324197 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]()
Wiring diagrams, connector pinouts, wire colors, etc are in the FSM. Link in my sig.
__________________
Steering Lock Links - Search The370Z Bookmarklet - FSM @ NICOclub Mankind has progressed past the need for war but we haven't evolved that far. - NachoMahma |
![]() |
![]() |
![]() |
#3 (permalink) |
Base Member
Join Date: Apr 2021
Location: Kentucky
Posts: 2
Drives: 2010 370z White auto
Rep Power: 4 ![]() |
![]()
I have replaced the VVEL module, both relays, cleaned the 2-Cam sensors. Same two codes P1606 and U1003. I am reading about the negative battery post and the screw could be causing the issues. Also consider the ECM was even remapped.
|
![]() |
![]() |
![]() |
#4 (permalink) |
Base Member
Join Date: Jan 2016
Location: Ontario
Posts: 230
Drives: G37 Sport
Rep Power: 6720 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]()
Assuming that the replacement VVEL module is good, I would focus on the wiring. Verify the module has 12v on pin 1, 8 and 13 with ignition on, engine off. Make sure to use the ground on pin 14.
Pins 11 and 24 are the dedicated CAN bus that runs from the ECU to the VVEL module. • With the battery disconnected, the resistance between pins 11 and 24 should be around 60 ohms. This verifies the CAN bus wires and proper bus termination. • With the battery connected and engine running, check the voltage between pin 11 + 14 (ground) and pin 24 + 14 (ground) You should see around 2.2V for CAN-Low and 2.7V for CAN-High. |
![]() |
![]() |
![]() |
Bookmarks |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Help with Airbag Diagnostic Code | vidwiz | Exterior & Interior | 11 | 09-22-2020 01:55 AM |
TOAD diagnostic scanner | Akshaya | Engine & Drivetrain | 15 | 07-17-2018 04:18 PM |
Codes and more Codes? now no start... | instroke | Forced Induction | 15 | 10-15-2015 10:51 PM |
Diagnostic software? | ARFCOM | Nissan 370Z General Discussions | 6 | 08-01-2010 01:52 PM |
Having trouble picking a Z.. and having trouble with the manual | AceSpade77 | Nissan 370Z General Discussions | 12 | 08-04-2009 04:02 PM |