Completed So Far

firulice · 02-14-2015, 03:13 PM

Quote:

Originally Posted by androger

Thanks firulice! Unfortunately, no. But I have no plans on selling this one, so resale value doesnt really affect me ;-) well unless some unforeseen event comes up... but I'd sell the Q7 before I sold this one lol

Good call

androger · 03-13-2015, 03:18 PM

So, since I work 7 days a week for the majority of each month, we have a four day weekend every so often . Yesterday, I spent about five hours tearing the car apart. I took the driver side pillar finisher off and realigned it. Replaced the lock pillar (I had ordered a new one because I knew I would end up breaking the old one), and aligned the hood and fenders so that they were aligned in accordance with the service manual. Now that everything is aligned at the windshield and pillar finishers, things are still off where the bumper meets the hood. At first I thought that the hood alignment was to blame, but now I am thinking that the radiator core support is shifted towards the driver side. I ran out of time, since I had some errands to run, but will rip it apart this weekend and see if I can line everything up again. Its only off a 1/4 of an inch, but it is enough to annoy me.

On a side note I recieved my RJM clutch pedal. I'll try to install that this weekend as well. I have also started my wish list:

AEM intake
24 row oil cooler
HKS 3 inch exhaust (may pick up the one in the classifieds)
Fuji front bumper (partial carbon)
AMS sides and rear (partial carbon)

hope everyone is doing well and thanks for reading!

Dragon_Ball_Z · 03-13-2015, 03:29 PM

Good luck on your build!

-Raj

androger · 03-13-2015, 03:35 PM

Thanks Raj!

03-13-2015, 03:18 PM	#17 (permalink)
androger Base Member Join Date: Jan 2015 Location: california Posts: 27 Drives: 40th 370z Rep Power: 10	So, since I work 7 days a week for the majority of each month, we have a four day weekend every so often . Yesterday, I spent about five hours tearing the car apart. I took the driver side pillar finisher off and realigned it. Replaced the lock pillar (I had ordered a new one because I knew I would end up breaking the old one), and aligned the hood and fenders so that they were aligned in accordance with the service manual. Now that everything is aligned at the windshield and pillar finishers, things are still off where the bumper meets the hood. At first I thought that the hood alignment was to blame, but now I am thinking that the radiator core support is shifted towards the driver side. I ran out of time, since I had some errands to run, but will rip it apart this weekend and see if I can line everything up again. Its only off a 1/4 of an inch, but it is enough to annoy me. On a side note I recieved my RJM clutch pedal. I'll try to install that this weekend as well. I have also started my wish list: AEM intake 24 row oil cooler HKS 3 inch exhaust (may pick up the one in the classifieds) Fuji front bumper (partial carbon) AMS sides and rear (partial carbon) hope everyone is doing well and thanks for reading! Dragon_Ball_Z likes this.

03-13-2015, 03:29 PM	#18 (permalink)
Dragon_Ball_Z A True Z Fanatic Join Date: Jul 2014 Location: Mississippi Posts: 1,117 Drives: Nismo& Sport/Touring Rep Power: 17	Good luck on your build! -Raj __________________ Build in Progress

03-13-2015, 03:35 PM	#19 (permalink)
androger Base Member Join Date: Jan 2015 Location: california Posts: 27 Drives: 40th 370z Rep Power: 10	Thanks Raj! Dragon_Ball_Z likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Sub Box Build install Completed	Tokugawa	Nissan 370Z Roadster (Convertible)	15	02-12-2015 09:00 AM
Bat's FANG and ROOF Overlays finally completed!	Bluebatmobile	Exterior & Interior	70	01-22-2011 07:27 PM
Completed Dynamat Extreme install, my thoughts.	Guard Dad	Audio & Video	13	10-05-2010 10:15 AM
Toyota FT-86 set for November 2011 release. Development is 50% completed.	1bad350z	Other Vehicles	9	07-26-2010 09:25 AM
Completed my break in period today!	TARDCORE	The Lounge (Off Topic)	16	01-30-2010 03:58 PM