Nissan 370Z Forum - View Single Post

Genosphere · 01-31-2018, 09:18 AM

I figure I try and show a few things they may not have been covered here earlier and try to provide some images where I can.

For some reason every time I try to add photos, the post dosent go through. So I added a new link at bottom with images. Sorry.

Hole drilled in main light fixture fir halo wires.

Demon eye: Drilled two holes, one for the bolt and another safety wire to hold it in place. (This did not work for me because I did not position it far enough forward, if there was even enough space, where I was trying to shine the light into the small opening in the projector shroud.

Never the less, try it and maybe you can get it to work.

Here is how I had things wired,

I wired into the car harness at each plug, GREEN=(+)Turn signal & RED=(+)HID on R/H light. The L/H light is different, I honestly dont remember but compare the plug to R/H and the wire positions are the same, looking at the end of the plug with the clip on top the bottom middle THICK wire is (+)HID and top left is the signal.

I was going to use the quick splicers, those blue things, but decided to just strip some of the wiring away and solder leads right onto the harness, more secure that way.

Now I wired the (+)Lead from the Morimot BT controller into the harness at the battery bay, should be the wire bundle most outboard going through the battery wall FWD. I removed some of the tape and what not and found a thick red wire that belongs to the radiator fan that has constant power once the car is on.

I ran all the wires upfront and "mounted" them to the front bumper, only place I found to have enough space to store all this ****, controller, and the six ballasts for the halos and demon eyes. There is room on each side above the black plastic flapper looking things.

I used 3M tape that sticks to its self and a couple zip-ties to secure them, and a bunch more zip-ties to hold all the wiring in place. An as you can see, I wrapped the whole damn thing in plastic to protect it as much as I can from water and debris, taped each end.

I modded the pumper a little to accommodate the zip-ties and plastic stuff, just for away some of the ridged that would sit inside the metal bumper's valley.

An I also used the horns mount as my ground for the DEMON EYES.

Not sure if the images will shot, using google drive as my source, so ill fix it when i get a chance. Should still be able to copy the link and view the images. If I can round up some more images or I made mistake, please let me know, Ill add more as I find it and get time.

Heres the link to the folder with images if the previous links did show:
https://drive.google.com/open?id=1ni...dev3YE1Mqlv-a_

Hope this helps anyone in any way.

01-31-2018, 09:18 AM	#655 (permalink)
Genosphere Base Member Join Date: Jul 2017 Location: Pittsburgh Posts: 32 Drives: 09 Z34 Black M Rep Power: 8	Trying this again I figure I try and show a few things they may not have been covered here earlier and try to provide some images where I can. For some reason every time I try to add photos, the post dosent go through. So I added a new link at bottom with images. Sorry. Hole drilled in main light fixture fir halo wires. Demon eye: Drilled two holes, one for the bolt and another safety wire to hold it in place. (This did not work for me because I did not position it far enough forward, if there was even enough space, where I was trying to shine the light into the small opening in the projector shroud. Never the less, try it and maybe you can get it to work. Here is how I had things wired, I wired into the car harness at each plug, GREEN=(+)Turn signal & RED=(+)HID on R/H light. The L/H light is different, I honestly dont remember but compare the plug to R/H and the wire positions are the same, looking at the end of the plug with the clip on top the bottom middle THICK wire is (+)HID and top left is the signal. I was going to use the quick splicers, those blue things, but decided to just strip some of the wiring away and solder leads right onto the harness, more secure that way. Now I wired the (+)Lead from the Morimot BT controller into the harness at the battery bay, should be the wire bundle most outboard going through the battery wall FWD. I removed some of the tape and what not and found a thick red wire that belongs to the radiator fan that has constant power once the car is on. I ran all the wires upfront and "mounted" them to the front bumper, only place I found to have enough space to store all this ****, controller, and the six ballasts for the halos and demon eyes. There is room on each side above the black plastic flapper looking things. I used 3M tape that sticks to its self and a couple zip-ties to secure them, and a bunch more zip-ties to hold all the wiring in place. An as you can see, I wrapped the whole damn thing in plastic to protect it as much as I can from water and debris, taped each end. I modded the pumper a little to accommodate the zip-ties and plastic stuff, just for away some of the ridged that would sit inside the metal bumper's valley. An I also used the horns mount as my ground for the DEMON EYES. Not sure if the images will shot, using google drive as my source, so ill fix it when i get a chance. Should still be able to copy the link and view the images. If I can round up some more images or I made mistake, please let me know, Ill add more as I find it and get time. Heres the link to the folder with images if the previous links did show: https://drive.google.com/open?id=1ni...dev3YE1Mqlv-a_ Hope this helps anyone in any way.