Nissan 370Z Forum - View Single Post

synolimit · 11-04-2016, 09:16 AM

Here, my saved list is easier.
Front -2.9 camber, 0.05* toe out, 6.5 caster
Rear -1.8 camber, 0.05* toe in
3080lbs, 1750lbs front, 1330lbs rear, no corner balance yet

2013 Sport 6mt
Engine----
OBX LTH with DEI titanium wrap
Motordyne XYZ Y pipe with DEI titanium wrap
Custom single 3" side exit exhaust, 1- 18" bottle res, 1 ultra quiet res, DEI titanium wrap
Stillen gen 3 CAI with DEI gold wrap
My dual AOS setup
My PnP TB, upper and lower manifolds
My 48 row oil cooler
CJ motorsports large baffled oil pan
Venting valve vents to atmos
Gas tank cut in half for fuel starve fix
Gas tank vent line with Boyd rollover vent/check valve
Redline 5w30 oil
CSF triple pass radiator
Tuned by Crucial Performance

Drive----
My rear 25 row diff cooler/Tilton pump with temp gauge
SPL solid diff bushings
Drop Eng. poly tranny mount
Redline diff fluid
Redline tranny fluid
Z1 solid engine mounts

Suspension----
Stance 2 way true type coilovers 18k/8k
SPL toe links
SPL traction arms
SPL rear chamber arms
Hotckins front sway bar
OEM rear sway bar
SPL camber arms front
SPL rear knuckle bushings
SPL front end links
My rear eccentric lock out kit
Traction and yaw kill switch

Brakes-----
Z1 SS brake lines
Front brake cooling ducts
Rear brake cooling ducts
Rbf600 fluid
Z1 2 piece rear rotors
Z1 2 piece front rotors
Carbotech XP12 front pads and XP10 rear pads
ABS system delete with Wilwood proportional valve

Aero----
My Front splitter
My Canards
My complete flat bottom
My rear diffuser
APR 71" GT-250 wing chassis mounted
Vented upper bumper for CAI and top of radiator

Wheels/tires
RPF-1 18x10.5 +15 square but rear is -30
RS-3's 285/35/18 square
45mm rear spacer with 10.9 hardware
3" ARP extended rear wheel studs

Safety
OMP fiberglass FIA halo seat.
OMP 6 point FIA belt with 2" shoulder straps for Hans device.
Hans III device.
OMP belt with 8.8 ring hardware
10.9 hardware holding seat to raisers and base.
Planted FIA steel base
Planted FIA aluminium raisers.
FIA 1.75" roll cage

Misc.
Rear wide body fenders
Deka 11lbs battery
E-brake delete
Full car air bag system delete
All non essential wires deleted throughout
Vinyl wrapped
AC system deleted along with two pulleys

Wanted.
Wavetrac rear diff
275/35/18 A7's
Spare set RPF1's
Corner balance
Wind tunnel

11-04-2016, 09:16 AM	#31 (permalink)
synolimit A True Z Fanatic Join Date: May 2013 Location: Columbus, OH Posts: 5,051 Drives: 2013 Silver 370z Rep Power: 3389	Here, my saved list is easier. Front -2.9 camber, 0.05* toe out, 6.5 caster Rear -1.8 camber, 0.05* toe in 3080lbs, 1750lbs front, 1330lbs rear, no corner balance yet 2013 Sport 6mt Engine---- OBX LTH with DEI titanium wrap Motordyne XYZ Y pipe with DEI titanium wrap Custom single 3" side exit exhaust, 1- 18" bottle res, 1 ultra quiet res, DEI titanium wrap Stillen gen 3 CAI with DEI gold wrap My dual AOS setup My PnP TB, upper and lower manifolds My 48 row oil cooler CJ motorsports large baffled oil pan Venting valve vents to atmos Gas tank cut in half for fuel starve fix Gas tank vent line with Boyd rollover vent/check valve Redline 5w30 oil CSF triple pass radiator Tuned by Crucial Performance Drive---- My rear 25 row diff cooler/Tilton pump with temp gauge SPL solid diff bushings Drop Eng. poly tranny mount Redline diff fluid Redline tranny fluid Z1 solid engine mounts Suspension---- Stance 2 way true type coilovers 18k/8k SPL toe links SPL traction arms SPL rear chamber arms Hotckins front sway bar OEM rear sway bar SPL camber arms front SPL rear knuckle bushings SPL front end links My rear eccentric lock out kit Traction and yaw kill switch Brakes----- Z1 SS brake lines Front brake cooling ducts Rear brake cooling ducts Rbf600 fluid Z1 2 piece rear rotors Z1 2 piece front rotors Carbotech XP12 front pads and XP10 rear pads ABS system delete with Wilwood proportional valve Aero---- My Front splitter My Canards My complete flat bottom My rear diffuser APR 71" GT-250 wing chassis mounted Vented upper bumper for CAI and top of radiator Wheels/tires RPF-1 18x10.5 +15 square but rear is -30 RS-3's 285/35/18 square 45mm rear spacer with 10.9 hardware 3" ARP extended rear wheel studs Safety OMP fiberglass FIA halo seat. OMP 6 point FIA belt with 2" shoulder straps for Hans device. Hans III device. OMP belt with 8.8 ring hardware 10.9 hardware holding seat to raisers and base. Planted FIA steel base Planted FIA aluminium raisers. FIA 1.75" roll cage Misc. Rear wide body fenders Deka 11lbs battery E-brake delete Full car air bag system delete All non essential wires deleted throughout Vinyl wrapped AC system deleted along with two pulleys Wanted. Wavetrac rear diff 275/35/18 A7's Spare set RPF1's Corner balance Wind tunnel __________________ 13 370z- Last edited by synolimit; 11-21-2016 at 06:33 AM.