Nissan 370Z Forum - View Single Post - GReddy Twin Turbo 2011 Nismo installed and tuned @ Motion Lab

Motion Lab · 07-20-2012, 08:24 PM

Hello Z owners. We recently signed up as a supporter of these forums in light of some of the cool 370z projects we have been working on. This post is to highlight one of our most recent projects, a twin turbo 2011 nismo edition 370z for a local customer here in the Charlotte area. We decided to install the kit with the motor still in the car. Progress was happening quickly but I have some O.K. photos to share. We utilized the GReddy twin turbo kit, DeatschWerks 850cc injectors and 320LPH fuel pump, and the UpRev Osiris tuning suite.

We met Richard one day as he stopped by the shop. He had just picked up a Nismo 370z within the past few months and did the typical intake and exhaust mods but just wasnt happy with the gains. We discussed the different options available on the market. We started looking at the Stillen supercharger kits as we had just tuned a 2010 370z with their stage2 kit that hit 420WHP on a Mustang dyno. He liked the powerband, but wanted to have more potential in the future. We ended up deciding on utilizing the GReddy twin turbo kit. This kit was very complete (outside of a few small components left out during packaging) but did not include any fuel system modifications or tuning solution. We have been direct with DeatschWerks since the beginning of the year, and have had the UpRev software for over a year for some of the 350z projects we had been a part of. We turned to them to round out the necessary modifications to make this transformation complete

Pic of some of the GReddy components upon arrival:

Once the kit came in we had Richard drop the car off. We had our technician Nate inspect the kit and begin tear down. Since we were pulling the transmission out, we decided to give it a shot with the motor in the car. It was a tight fit but Nate worked diligently to get everything to fit as advertised.

We started by pulling the transmission to fit up the new clutch kit, and make our lives a little easier when it came to fitting the turbos. Then we started fitting the manifolds and installing the necessary heat shielding. Once we had everything mounted I went out and snapped a quick picture before Nate moved on.

This kit came with a new cast oil pan. Great looking piece and made installation of oil feed lines a snap. Increased the capacity by about a quart. This is where we ran into the first missing part, the oil pickup tube spacer. Because the pan actually sat lower, you needed to utilize a small machined spacer to keep the pick-up tube at the bottom of the sump. GReddy is all the way in California, and for the sake of time we went ahead and had our local machinist make us what we need. Its good to be in this area, as we are surrounded by talented individuals!

After that, we started to tackle the seemingly endless trail of aluminum piping. Intakes, intercooler, and intercooler piping was the last step after the fuel injectors and fuel pump. Took us roughly a day to finish up this part of the project as Nate is also somewhat of a perfectionist. Not a bad attribute to have in a technician

. This is also when we found the other two missing pieces out of the kit. Two reducer couplers. We needed an answer in a hurry, tough to match GReddy blue, so we went with a nice 4ply reinforced silicon reducer from Mishimoto. Unfortunately Samco was out of stock, and GReddy USA tends to move at a snails pace. Please excuse the color differences.

(Also check out the Evo 6 TME for you JDM lovers)

After that, unfortunately I dont have any pics, we fitted a Mishimoto low temp thermostat and Cosworth 1.3bar cap. Just want to make sure the cooling system was up to the task. After that, this build was just about wrapped up. We swapped in a set of DILKAR8A8 (GT-R plugs) for a more appropriate gap and then we started tuning.

After dialing in the injectors, MAF, and smoothing the ignition timing on the street it was time to strap it down and see what she was gonna do. Dyno runs were done in 4th gear on a Mustang 2WD dyno. Kit was only running wastegate pressure out the box. Final power numbers were 440whp and 339wtq at just 5.5PSI.

Final HP/TQ w/Boost plot:

Final HP/TQ w/ AFR plot:

Final HP/TQ vs baseline:

Here at Motion Lab we always like to take a step back and see what is really working. When Todd was at the dyno he overlayed the 2010 370z that we tuned with a Stillen stage2 kit versus the twin turbo equipped 2011 nismo that we just finished building. The good news is that both are exceptional quality kits that deliver the power advertised.

GReddy vs Stillen Stage2 kit:

After completion we tried our hand a little video editing. Glory did a great job editing a quick video to showcase the car a little and show a few pulls on the dyno. Hope you guys enjoyed this little expose on the Nismo Z we transformed. Please check out the YouTube video below!

Complete mod list:

GReddy twin turbo kit w/ TD06H-20G turbos and FMIC
DeatschWerks 850cc fuel injectors
DeatschWerks 320LPH fuel pump
Mishimoto Low temp thermostat
Cosworth 1.3bar radiator cap
ACT HDSS clutch kit
Motion Lab tuned via UpRev Osiris tuning suite

Thanks,
Alex Goodwin
AlexG@motionlabtuning.com
http://www.facebook.com/MotionLabTuning

07-20-2012, 08:24 PM	#1 (permalink)
Motion Lab A True Z Fanatic Join Date: Jul 2012 Location: Charlotte, NC Posts: 2,676 Drives: Nissan 370Z Rep Power: 18	GReddy Twin Turbo 2011 Nismo installed and tuned @ Motion Lab Hello Z owners. We recently signed up as a supporter of these forums in light of some of the cool 370z projects we have been working on. This post is to highlight one of our most recent projects, a twin turbo 2011 nismo edition 370z for a local customer here in the Charlotte area. We decided to install the kit with the motor still in the car. Progress was happening quickly but I have some O.K. photos to share. We utilized the GReddy twin turbo kit, DeatschWerks 850cc injectors and 320LPH fuel pump, and the UpRev Osiris tuning suite. We met Richard one day as he stopped by the shop. He had just picked up a Nismo 370z within the past few months and did the typical intake and exhaust mods but just wasnt happy with the gains. We discussed the different options available on the market. We started looking at the Stillen supercharger kits as we had just tuned a 2010 370z with their stage2 kit that hit 420WHP on a Mustang dyno. He liked the powerband, but wanted to have more potential in the future. We ended up deciding on utilizing the GReddy twin turbo kit. This kit was very complete (outside of a few small components left out during packaging) but did not include any fuel system modifications or tuning solution. We have been direct with DeatschWerks since the beginning of the year, and have had the UpRev software for over a year for some of the 350z projects we had been a part of. We turned to them to round out the necessary modifications to make this transformation complete Pic of some of the GReddy components upon arrival: Once the kit came in we had Richard drop the car off. We had our technician Nate inspect the kit and begin tear down. Since we were pulling the transmission out, we decided to give it a shot with the motor in the car. It was a tight fit but Nate worked diligently to get everything to fit as advertised. We started by pulling the transmission to fit up the new clutch kit, and make our lives a little easier when it came to fitting the turbos. Then we started fitting the manifolds and installing the necessary heat shielding. Once we had everything mounted I went out and snapped a quick picture before Nate moved on. This kit came with a new cast oil pan. Great looking piece and made installation of oil feed lines a snap. Increased the capacity by about a quart. This is where we ran into the first missing part, the oil pickup tube spacer. Because the pan actually sat lower, you needed to utilize a small machined spacer to keep the pick-up tube at the bottom of the sump. GReddy is all the way in California, and for the sake of time we went ahead and had our local machinist make us what we need. Its good to be in this area, as we are surrounded by talented individuals! After that, we started to tackle the seemingly endless trail of aluminum piping. Intakes, intercooler, and intercooler piping was the last step after the fuel injectors and fuel pump. Took us roughly a day to finish up this part of the project as Nate is also somewhat of a perfectionist. Not a bad attribute to have in a technician . This is also when we found the other two missing pieces out of the kit. Two reducer couplers. We needed an answer in a hurry, tough to match GReddy blue, so we went with a nice 4ply reinforced silicon reducer from Mishimoto. Unfortunately Samco was out of stock, and GReddy USA tends to move at a snails pace. Please excuse the color differences. (Also check out the Evo 6 TME for you JDM lovers) After that, unfortunately I dont have any pics, we fitted a Mishimoto low temp thermostat and Cosworth 1.3bar cap. Just want to make sure the cooling system was up to the task. After that, this build was just about wrapped up. We swapped in a set of DILKAR8A8 (GT-R plugs) for a more appropriate gap and then we started tuning. After dialing in the injectors, MAF, and smoothing the ignition timing on the street it was time to strap it down and see what she was gonna do. Dyno runs were done in 4th gear on a Mustang 2WD dyno. Kit was only running wastegate pressure out the box. Final power numbers were 440whp and 339wtq at just 5.5PSI. Final HP/TQ w/Boost plot: Final HP/TQ w/ AFR plot: Final HP/TQ vs baseline: Here at Motion Lab we always like to take a step back and see what is really working. When Todd was at the dyno he overlayed the 2010 370z that we tuned with a Stillen stage2 kit versus the twin turbo equipped 2011 nismo that we just finished building. The good news is that both are exceptional quality kits that deliver the power advertised. GReddy vs Stillen Stage2 kit: After completion we tried our hand a little video editing. Glory did a great job editing a quick video to showcase the car a little and show a few pulls on the dyno. Hope you guys enjoyed this little expose on the Nismo Z we transformed. Please check out the YouTube video below! Complete mod list: GReddy twin turbo kit w/ TD06H-20G turbos and FMIC DeatschWerks 850cc fuel injectors DeatschWerks 320LPH fuel pump Mishimoto Low temp thermostat Cosworth 1.3bar radiator cap ACT HDSS clutch kit Motion Lab tuned via UpRev Osiris tuning suite Thanks, Alex Goodwin AlexG@motionlabtuning.com http://www.facebook.com/MotionLabTuning