See 2nd Post for Fast Intentions Install.
Hi all, Firstly I want say I added the Fast Intentions Exhaust to the title even though I have gotten that in yet. Hopefully it should be close to the first week of Sept sometime and didn’t want to start a whole new thread on it. Also it will give a great comparison for everyone to see.
Now on to the fun stuff. I received the 3* (Aus370 and Ellz) Stillen G3 Long Tube Intakes yesterday from
Import Parts Pro (big props to
Kyle
for all his help with this). We had a few issues on our end in Australia with banking and exchange rates. Kyle couldn't have been more accommodating and helpful with this. The packaging was first rate and not a mark or scratch on any of the parts at all.
Also a big shout out to
Hi-Power Performance at Slacks Creek who were able to get all 3 of us in and done yesterday. With no warning I turned up there with my Car Dealer who knew them and they were very happy and helpful in getting it done straight away
.
Delivered,
Packaging,
Parts,
Now for the install itself it pretty much went off without a hitch at all. Basically pretty much everything was as per the instructions that you get with the kit. We didn't even have to cut quite as much for the intake piping to go through (Photo 4 in the instructions). Another thing we decided to do was cut off part of the screw (a couple of mm) that holds the Horn as it protrudes a bit into the Pod filters themselves, with that done the Pods just rest on it now. Other than the above it took a bit longer to do mine as it was the first one they had done, then the others guys cars they just flew through it.
There were a couple of things to be a little careful of say like the Front Airbag sensor for example which are not in the Instructions. Mind you this could be because our cars a slightly different to the US counterparts.
Before Front End,
Engine Bay Before,
Left Intake Off,
Right Intake Off,
Front End Off,
Right Side Done,
Left Side Done,
Pods Close Up,
Pods With Bumper Back On,
Installed,
I was also lucky enough that the owner of the Workshop wanted to see what the car would do and offered to do a Power run for a before and after comparo. It was a very warm day for this time of year in Aus. The temperature was at 34c+ (94.2f) in the Dyno area, outside ambient was about 32c. I am personally very happy with both the Stock run (before) and after run of the car. The numbers are pretty much bang on to what the guys in US are getting. With generally our Dynos reading slightly lower.
To be honest Dynos for me are just a tuning tool and to help give an idea of gains seen from certain parts. I just hope when we get the Exhausts done, that the temp/humidity is very much similar to give a fair comparison.
So here is the first run a before if you will,
Prepping for Dyno,
Dyno with Bumper ON,
Before,
With Parts Installed,
So we see an increase of 15atwhp. Also there was a slight increase in Torque. All the gains were in the Top end, say the last 1500rpm which is what I personally expected. On the road I do believe there is noticeable difference, not so much in all out power but more on delivery. It does feel a decent amount more responsive all through the rev range.
You do have a nice induction noise under full throttle, which also adds a small amount to the exhaust side of things as well. At cruising speeds 40,60,80,100kmh it sounds no different to stock, until you actually prod the throttle a bit. Theres is also definite room for improvement in the fueling side of things. It appears we run very RICH in Aus, which is probably just Nissan playing it safe with a lot of our fuel being crappy and playing to the lowest common denominator.
Now hopefully only a couple more weeks for the Fast Intentions, Resonated Test Pipes, 18” Resonator Exhaust with CF Mufflers. Once that is in I’ll update a 2nd post below with numbers and pics. I’ll also try and get my hands on proper Video Camera for the Dyno Runs, plus do some drive bys as well.
All the Stillen G3 Intake
PHOTOS.